Posts Tagged ‘Oklahoma City French Drain’


French Drain Installation in Oklahoma City, Norman, Yukon, Mustang, Edmond, Lawton

Oklahoma Drainage and Sprinkler Repair 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

    Sprinkler Repair for all aspects of Residential Sprinkler Systems

    Emergency Sprinkler Repair Service, AFTER HOURS AND WEEKENDS.

A good place for a French Drain

A Channel Drain Across the, soon to be installed driveway would be a good idea too!

channel drain driveway

Channel Drain set in Driveway

FRENCH DRAIN  CONNECTED TO GUTTERS

French Drain protects sidewalk

French Drain keeps water off of sidewalk

Many different types of Drains can be hooked together by one Drain Pipe.  The Drain Pipe then running to an Exit Point makes up a Drainage System.  One common type of Drain used in a Drainage System is A “French Drain.”  Many times a French Drain is installed close to a building foundation or in a low area next to a home or business.  This puts the French Drain in close proximity to Gutter Down Spouts.  Rather than have water come off the roof and out the Down Spout and on to the ground below, many times it is much better to tie a Gutter Down Spout Directly into a French Drain or near by Drain Pipe depending on the Drainage System Design.   Connecting The Down Spouts Directly into a French Drain is much  more efficient and causes suction to occur in the French Drain.  Connection of Gutter Down Spouts to a French Drain makes the Drainage System work better.

 

 

French Drain Before gravel is installed Drainage Systems can:

1.  Keep water away from foundations — A French Drain is best because it can move Surface Water and Sub-Surface Water (water moving under ground) away from the foundation.  Many times less experienced companies install Surface Drains to keep water away from foundations.  This can be a big mistake.  A Surface Drain can’t move or drain Sub-Surface Water.   Also A Surface Drain often can’t move enough water fast enough and easily becomes overwhelmed during a heavy rain.  A Surface Drain also can’t cover or protect a broad enough area. Surface Drains should be designed in a Drainage System to be located in smaller Drainage Areas moving moderate amounts of water.  Surface Drains look better than French Drains.  If ,”appearance” is more important than Drainage Capacity, Go with the Surface Drain.  Just know what you are getting into and what your expectations should be. One side of a foundation alone,  can be over 100 feet.  A 4 inch or 6 inch French Drain is best when protecting a large area such as a foundation.

Surface Drain Installed next to sidewalk in Oklahoma City.

Surface Drain along sidewalk

Surface Drain Installed next to sidewalk in Oklahoma City.

2.  Keep water away from small or enclosed areas.  This might be a low area just through a gate on the side of a house, or the low area between a flowerbed and the wall of a house, or standing water on or near a sidewalk or driveway.  These types of Drainage Problems are best served with Surface Drains.  A Surface Drain can move water away from a low area that is relatively small.  This can occur in yards, flowerbeds, sidewalks and driveways.  A Surface Drain is designed to move Surface Water away from a problem area to a predetermined exit point.  Surface Drains are available in many sizes.  How quickly they remove standing water is usually determined by the size of the Drain Pipe that is connected to the Drain.

Surface Drain Installation in Norman

French Drain Installation in Oklahoma City, Norman, Yukon, Mustang, Edmond, Lawton

Oklahoma Drainage and Sprinkler Repair 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

    Sprinkler Repair for all aspects of Residential Sprinkler Systems

    Emergency Sprinkler Repair Service, AFTER HOURS AND WEEKENDS.

A good place for a French Drain

A Channel Drain Across the, soon to be installed driveway would be a good idea too!

Channel Drain set in Driveway

FRENCH DRAIN  CONNECTED TO GUTTERS

Many different types of Drains can be hooked together by one Drain Pipe.  The Drain Pipe then running to an Exit Point makes up a Drainage System.  One common type of Drain used in a Drainage System is A “French Drain.”  Many times a French Drain is installed close to a building foundation or in a low area next to a home or business.  This puts the French Drain in close proximity to Gutter Down Spouts.  Rather than have water come off the roof and out the Down Spout and on to the ground below, many times it is much better to tie a Gutter Down Spout Directly into a French Drain or near by Drain Pipe depending on the Drainage System Design.   Connecting The Down Spouts Directly into a French Drain is much  more efficient and causes suction to occur in the French Drain.  Connection of Gutter Down Spouts to a French Drain makes the Drainage System work better.


French Drain Installation, Drainage Systems, Surface Drain, Sump pumps, – Oklahoma Drainage and Sprinkler Repair

Before

cutting the driveway for a channel drain

Breaking out the cut concrete

After

channel drain driveway

 

Hard rain and flooding seem to be more common all the time.  When I started this business in 1993, having over an inch of rainfall in an hour was pretty extreme.  Now having over 4 inch an hour rainfall is not unheard of and is becoming more common.

Gutter to French Drain

Connecting Gutter to French Drain

Oklahoma Drainage and Sprinkler Repair has seen and dealt with virtually every possible Drainage and Standing water problem that can occur in or around your home.  With over 2000 Drainage Systems installed since 1993, we have amassed a great deal of experience.  This is help full in seeing underlying problems and secondary issues that may be hard to see at first for the ” Untrained Eye.”  This allows us to get things right the first time.  In this business EXPERIENCE TRULY COUNTS!

Hiring your brother in law to put in your Drainage System or French Drain is as bad as hiring a Lawn mowing company that does landscaping and drains too?  Water can cause a huge amount of damage.  How important is your money and your home?

Blane Callen, 405 203 9419

Is this your yard?

This is a great place for a French Drain

Oklahoma Drainage and Sprinkler Repair designs and installs Drainage SystemsWater Drainage is a big concern to home owners and small businesses. Standing Water from Storm-Water runoff can cause all kinds of problems.  Concrete in driveways, sidewalks, and foundations can be damaged.  Prolonged Drainage Problems allow mold to occur along with deterioration to plants, trees, and property.

Just what is a “French Drain?”  Many times people incorrectly use the phrase, “French Drain,”  to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drain Pipe is connected underground to an outlet on the Drain Basin.  Storm-Water Drains through the grate into the Drain Basin.  Once in the Drain Basin, water travels out of the basin through a Drain Pipe.  The Storm-Water continues downhill in an underground Drain Pipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

A Channel Drain is a type of Surface Drain and many times is installed in concrete across sidewalks or driveways.

French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain Pipin the bottom of a trench.  The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe.   This is to ensure that the Drain Pipe does not become clogged.

The dirt that was taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed.

French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.
 
The main downfall of a French Drain is that they, for the most part aren’t very pretty.  They don’t look very nice in a yard once they are completed.
Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the lime stone.  Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel.  This is Ok.  It won’t have a measurable effect on the performance of the drain.
DON’T COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT.  THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT.  DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.

DECORATIVE STONE CAN BE USED TO COVER A FRENCH DRAIN AND THEY LOOK GREAT AND LAST A LIFETIME.

French Drains Can Look Great!

 


A NEW FRENCH DRAIN IN OKLAHOMA CITY

Recently we installed a large Drainage System in OKC.  It was a 4 inch System using 4 inch ADS French Drain Pipe with Soc and 4 inch ADS Solid Drain Pipe.  The “Intake” of the Drainage System had two parts.  Water from the gutters on the house was fed into the Drainage System.  There were 7 gutter downspouts around the entire house that were connected straight into the Drainage System with Solid Drain Pipe and a Gutter connection.

French Drain Installation In Yukon

Oklahoma Drainage and Sprinkler Repair : Servicing all of Central and Western Oklahoma since 1993.

Standing Water on Your Driveway?  A Surface Drain set in concrete may be what you need. Or maybe you need a French Drain Running alongside your driveway instead.  Handling water problems is what we are good at.  If you need help, Oklahoma Drainage can provide the best solution for your unwanted water problems.

 

standing water

A good place for a French Drain

French Drain protects sidewalk

French Drain keeps water off of sidewalk

We just finished a 4 inch Drainage System in Yukon.  It was a complicated system to install.  It utilized 4 inch French Drain in the flower beds,  12 inch Surface Drains on the side of the house,  6 inch French Drain along the garage foundation with 2 Pop – Up Emitters in the back yard and 3 Curb Fittings in the front.    First we installed 4 inch French Drain in the flowerbeds on both sides of the front door.  We connected 4 inch solid Drain Pipe into the French Drain and ran them underside walk to the curb.  Next we cut the curb with a concrete saw and installed 3 curb outlets for 3 separate French Drains.

Next we installed 4 12 Inch Drain Basins with grates along both sides of the house continuing with Solid Drain Pipe to the Pop-Up Emitters on the back fence. Finally we completed the Drainage System by installing a long run of 6 inch French Drain down the side of the garage foundation.   Installing the French Drains in the flower beds was the most difficult and took the most time.  Each French Drain took over a ton of crushed limestone to fill the French Drain trench.  The Six inch French Drain took even more limestone.

 Oklahoma Drainage and Sprinkler Repair

Hey Oklahoma, We are expanding to service all of Western Oklahoma as well as Central Oklahoma.  If you live in Elk City, and need a French Drain, we can help.  If water is standing on your driveway in Clinton, Give us a call.  Duncan, Lawton, and Altus are all new areas of service for us.

Since 1993 Oklahoma Drainage and Sprinkler Repair has solved all types of standing water and drainage issues.  We install Drainage Systems that utilize French Drains, Surface, Drains, Channel Drains, and Sump Pumps depending on the customers needs.

If you have water in the wrong place , we can help!

We also have Decades of experience repairing all types of Lawn Sprinkler Problems.  Fixing broken sprinkler heads, sprinkler valve problems and controller trouble just to name a few things.

French Drains as part of a Drainage System – 

Many times people use the term ” French Drain” as general name for a Drain used in or around your home.  French Drains are designed to move a lot of water over a large flooded area.  They are also designed to take water in on the surface of the ground or below the surface of the ground.  This is very important if the water coming into the flooded area is moving through the ground or coming up from underneath.  ” Sub Surface Water Movement.”  The picture below is not a French Drain!

 
Gutter to French Drain
Connecting Gutter to French Drain

Oklahoma Drainage  installs a variety  of Drains.  Our Drainage Systems may utilize: French Drains, Surface Drains, Channel Drains, Trench Drains, Basin Drains, and Sump Pumps.  In the past 21 years, we have installed French Drains to keep water away from home and business foundations, Surface Drains to keep water away from sidewalks and driveways,  Trench Drains, and French Drains to keep standing water out of flowerbeds and yards, and Sump Pumps to remove water from basements and outdoor low lying areas.

French Drain with stepping stones
French Drain with stepping stones

French Drains can be installed by themselves, or as part of a Drainage System that uses other French Drains, Surface Drains, or other Drain combinations.  Typically a French Drain is used to protect a broad area that has a lot of standing water.  A French Drain might run along side a homes foundation, or beside a driveway, or on any Drainage Project where Sub-Surface water is the primary problem.  If water is running toward your home under ground ( through sandy soil), A French Drain is the only Solution  for draining away water flowing under ground.

6 Inch French Drain
6 Inch French Drain

If you live in Oklahoma City and need a French Drain installed in your yard, or along your driveway, or near your foundation, give Oklahoma Drainage a call.  If you live in Edmond or Norman and need a Surface Drain installed in the concrete in your sidewalk or driveway, we can help.  If you live in Mustang or Yukon and would like to protect your trees or flower beds from standing water with a French Drain,

Installing concrete around drain
Installing wet concrete around channel drain
Channel Drain Installation in Sidewalk
Channel Drain Installation in Sidewalk

Oklahoma is famous for it’s powerful thunderstorms and heavy downpours. Storm-water runoff causes a variety of DRAINAGE PROBLEMS for Home and Business owners.

This front yard needs a french drain!

DRAINAGE PROBLEMS come in a wide variety of forms. You might have water standing in your backyard after a thunderstorm. Water from your gutter-downspouts may be turning your sidewalk into a “Moat.” Or, worst of all, Standing Water may be seeping into your home. WE can help!

Drainage solutions sometime require one or several types of drains to solve the problem. Oklahoma Drainage and Sprinkler Repair has been successfully solving DRAINAGE PROBLEMS since 1993. We can quickly diagnose your DRAINAGE PROBLEM and design a DRAINAGE SYSTEM to solve your DRAINAGE PROBLEMS. WE UTILIZE: FRENCH DRAINS, SURFACE DRAINS, CHANNEL DRAINS, BASIN DRAINS, TRENCH DRAINS, BASEMENT DRAINS, AND SUMP PUMPS.

Sump and French Drain
Sump Pump connected to french drain

 

Gutter to French Drain

Connecting Gutter to French Drain

 

new curb outlet

Curb outlet with more than 6 inches of fall

 

 

 

 

Drainage System Installation in Norman

Drainage System Installation in Norman

 

 

Standing water comes from many sources.  It causes damage to sidewalks, driveways, and foundations not to mention plants, trees, and grass.

Does the side of your house flood because your neighbor doesn’t have gutters, or does your sidewalk turn into a moat after a heavy rain, or worst of all, does water seep into your foundation and duct work after a thunderstorm.  Theses are just a few of the Drainage Problems that Oklahoma Drainage can help with.

Just what is a “French Drain?”  Many times people incorrectly use the phrase, “French Drain,”  to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drain Pipe is connected underground to an outlet on the Drain BasinStorm-Water Drains through the grate into the Drain Basin.  Once in the Drain Basin, water travels out of the basin through a Drain Pipe.  The Storm-Water continues downhill in an underground Drain Pipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

 

A Channel Drain is a type of Surface Drain and many times is installed in concrete across sidewalks or driveways.

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench.  The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe.   This is to ensure that the Drain Pipe does not become clogged.

The dirt that was taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed.

French Drain

A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it. The main downfall of a French Drain is that they, for the most part aren’t very pretty.  They don’t look very nice in a yard once they are completed.Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the lime stone.  Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel.  This is Ok.  It won’t have a measurable effect on the performance of the drain.  DONT COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT.  THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT.  DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.

 


Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.

French Drains as part of a Drainage System – 

Many times people use the term ” French Drain” as general name for a Drain used in or around your home.  French Drains are designed to move a lot of water over a large flooded area.  They are also designed to take water in on the surface of the ground or below the surface of the ground.  This is very important if the water coming into the flooded area is moving through the ground or coming up from underneath.  ” Sub Surface Water Movement.”  The picture below is not a French Drain!

A French Drain looks like this

Recently Oklahoma Drainage and Sprinkler Repair Installed a French Drain as part of a Drainage System in Mid West City Oklahoma.

Our customer had a back porch Sun Room.  Every time he had a hard rain, Water would run in one door and out the other.  An indoor creek across his Sun Room.

French Drain protects sidewalk
French Drain keeps water off of sidewalk

We installed a French Drain in front of the South Door.  It was 26 feet long and ran from a gutter downspout which it was connected to,  in front of the South Door and along the house covering the entire “Low” Area.  Then we connected 4 inch ADS Solid Drain pipe to the French Drain and ran down hill around the corner of the house to the street.

pipe to street
French Drain pipe running to street

Once the 4 inch solid drain pipe was connected to the French Drain and the two gutter down spouts, a pop-up emitter was installed to release the water at the street.

The next step was to cover the drain pipe with dirt and put the sod back in place on top of the pipe.   There was about 8 wheelbarrows of dirt left over that was displaced by the drain pipe and the French Drain.  The extra dirt was scooped up and hauled away.

While installing the drainage system, it was necessary to move two sprinkler heads that were in the way of the drain pipe installation.  This was no problem.  Installing drainage systems and French drains for folks who have a sprinkler system is very common.  Moving Sprinkler heads or pipes sometimes is necessary.  We always leave the sprinkler system in complete working order and we discuss any changes in the sprinkler system with the customer before we do it to make sure that everyone is on the same page.  In most cases the customer cant tell that we made any changes to the sprinkler system at all.

connecting gutter to French Drain
Drainage System Installation in Norman
Drainage System Installation in Norman

Harsh weather in Oklahoma seems to becoming more common.  In 2013,  Norman Oklahoma had 4 inches of rain in two hours.  That’s the most rain in a short time that I can remember.  Storm-Water runoff can cause damage to all types of property and buildings.  Water getting inside your house is never a good thing.  A Drainage System that utilizes a French Drain can help.

Drains can protect your home and property from water damage.

Large 6 Inch French Drain Installed in Norman
Large 6 Inch French Drain Installed in Norman

Drainage Systems can be made up of one drain or a combination of many drains.  Drainage  problems can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together.  Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together.

An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional Surface Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street.

A simple Drainage System might consist of a Surface Drain that is connected to a second Surface Drain which runs to a Pop-up Emitter which lets water drain over the curb and into the street.

An “Exit Point” is the term used for where all the water leaves the Drainage System.  Determining the Exit Point is very critical.  It is one of the first things we do when diagnosing a Drainage Problem.

Drainage Systems can:

1.  Keep water away from foundations — A French Drain is best because it can move Surface Water and Sub-Surface Water (water moving under ground) away from the foundation.  Many times less experienced companies install Surface Drains to keep water away from foundations.  This can be a big mistake.  A Surface Drain can’t move or drain Sub-Surface Water.   Also A Surface Drain often can’t move enough water fast enough and easily becomes overwhelmed during a heavy rain.  A Surface Drain also can’t cover or protect a broad enough area. Surface Drains should be designed in a Drainage System to be located in smaller Drainage Areas moving moderate amounts of water.  Surface Drains look better than French Drains.  If ,”appearance” is more important than Drainage Capacity, Go with the Surface Drain.  Just know what you are getting into and what your expectations should be. One side of a foundation alone,  can be over 100 feet.  A 4 inch or 6 inch French Drain is best when protecting a large area such as a foundation.

Surface Drain Installed next to sidewalk in Oklahoma City.
Surface Drain Installed next to sidewalk in Oklahoma City.

2.  Keep water away from small or enclosed areas.  This might be a low area just through a gate on the side of a house, or the low area between a flowerbed and the wall of a house, or standing water on or near a sidewalk or driveway.  These types of Drainage Problems are best served with Surface Drains.  A Surface Drain can move water away from a low area that is relatively small.  This can occur in yards, flowerbeds, sidewalks and driveways.  A Surface Drain is designed to move Surface Water away from a problem area to a predetermined exit point.  Surface Drains are available in many sizes.  How quickly they remove standing water is usually determined by the size of the Drain Pipe that is connected to the Drain.

Surface Drain Installation in Norman
Surface Drain Installation in Norman

Simply put, a Drainage System is one or a group of underground Drain Pipes that take water away from a place that has water standing on it or flowing across it.  The water that is in the problem area, can be causing damage or may be inconvenient or both.  (Usually Both)  A simple Drainage System is a Drain for the water to enter, a Drain Pipe to move the water away from the Drain, and an Exit Point for the water to be released out of the Drain Pipe.

Drainage Systems quickly can become more complicated.  Considerations must include:

How does the water get to the problem area?  There may be one or many sources.

Water Sources:

1.  It falls from the sky directly

2.  It flows down hill over the surface (surface water)

3.  It flows underground under the surface (sub-surface water)

4.  It flows from the edge of a roof ( There may be many roofs near the problem area, neighbors etc.)

5.  It flows from a gutter downspout

6.  It flows over the edge of a gutter because the gutter is too small is is clogged

7.  It flows up from the ground (seeps and springs are common in Oklahoma)

8.  It flows from a sprinkler system use ( yours or your neighbors)

9.  It flows from a leaking pipe ( water mains, water meters, water lines, sprinkler pipes, sprinkler valves)

There are other reasons for Drainage Problems, the above reasons are just the most common.

Once the number of water sources is determined, a rough estimate of the amount of water that needs to be drained away on average must be estimated.  This can be simplified down to “SMALL, MEDIUM, OR LARGE AMOUNTS OF WATER TO BE DRAINED AWAY.  You don’t have to be an engineer trying to calculate fluid dynamics.  Experience at diagnosing drainage problems helps however.  How much water needs to be moved will help determine the type and size of the Surface Drain or French Drain that needs to be installed.  It also helps to determine the size of Drain Pipe required for the Drainage System.  A good rule to follow is, “If in doubt, install a larger Drain and Drain Pipe.”  Unused Drainage Capacity is better than property damage caused by a Drain that is overwhelmed by too much water.

For home and small business use typical materials used are:

6 inch, 9 inch, and 12 inch Surface Drains

3 inch, 4 inch, and 6 inch Drain Pipes

3 inch, 4 inch, and 6 inch French Drains

French Drains move more water than Surface Drains —

French Drains move Surface Water and Sub-Surface Water

Surface Drains move Surface Water only

Surface Drains look nicer than French Drains in most cases

Once the type and number of drains is determined and what size Drain Pipe will connect them, an exit point must be selected.  (Where is the Drainage System going to take the water to and release it?)

The Drainage Curb Fitting is installed when the desired exit point for the French Drain will release the Drainage Water into the Street.   The Drainage Curb Fitting is rectangular in shape and made to be installed through the curb.  A small section of Curb is cut out with a concrete saw.  The Section is a few inches wider than the Drainage Curb Fitting.  We then install new concrete around the curb fitting.  Once the concrete has dried, the Drain Pipe coming from a French Drain or Surface Drain is connected to the Drainage Curb fitting and then covered with dirt.

Cutting The Curb and Installing Curb Fitting for French Drain
Cutting The Curb and Installing Curb Fitting for French Drain

The Drainage Pop-Up Emitter is connected to the end of a Drain Pipe.  It is downhill from a French Drain or a Surface Drain.  It is a small release basin with a green pop-up lid.  When releasing water, it pops up about an inch to release the water from the French Drain or Surface Drain.  When the Storm Water has moved through the Drainage System and out of the Pop-Up Emitter, the green lid closes back to its original closed position.  The emitter is designed to release water out into a yard or down a hill or other desirable Drainage Exit Point where there is no curb.

Popup Emitter to release water from a Drainage System in Yukon.
Popup Emitter to release water from a Drainage System in Yukon.

French Drain Installation Or Do You Need A Surface Drain?

Many Folks don’t know the difference.   Actually there are many differences and a few similarities.  One difference is, a French Drain takes in a larger amount of water into the drain Pipe than a Surface Drain.   A French Drain consists of water passing through gravel and into a perforated pipe below it.  The perforated Drain Pipe lies in a trench usually about 18 inches below ground but this can vary greatly depending on the variables and requirements of the French Drain.

Installed French Drain

French Drain Installed, Water is gone, just need to clean the mud off the sidewalk

A  Surface Drain is a Drain Receptacle with Grate that is connected to a solid drain pipe.

12 inch surface drain

12 Inch Surface Drain Installation

There are advantages to Surface Drains as well.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.

Oklahoma Drainage and Sprinkler Repair recently diagnosed a Drainage Problem in  South Oklahoma City.  The Home owner had a sump Pump in their basement that was fed from a French Drain outside the Basement Wall.  The French Drain was 14 feet down along the Stem wall of the house.  The French Drain Pipe was cheap and had collapsed.  We brought in a Mini Excavator and dug up the pipe and replaced it with Durable ADS 4 inch perf/soc French Drain pipe.  In the end, we were able to dig up the pipe and Replace it.

Gutter to French Drain
Connecting Gutter to French Drain
French Drain Detail
New Trench for French Drain

Next we installed a new exit for the water by installing a curb fitting.

No more flooding in the customers basement.  A few weeks later our customer was able to lay carpet in the basement with no problems.

French Drain side of House
French Drain Installed Along Stem Wall

Installing Drainage Curb Fitting for a French Drain in South Oklahoma City

curb cement outlet

Curb Fitting with Acrylic Cement For French Drain

FRENCH DRAIN  CONNECTED TO GUTTERS

Many different types of Drains can be hooked together by one Drain Pipe.  The Drain Pipe then running to an Exit Point makes up a Drainage System.  One common type of Drain used in a Drainage System is A “French Drain.”  Many times a French Drain is installed close to a building foundation or in a low area next to a home or business.  This puts the French Drain in close proximity to Gutter Down Spouts.  Rather than have water come off the roof and out the Down Spout and on to the ground below, many times it is much better to tie a Gutter Down Spout Directly into a French Drain or near by Drain Pipe depending on the Drainage System Design.   Connecting The Down Spouts Directly into a French Drain is much  more efficient and causes suction to occur in the French Drain.  Connection of Gutter Down Spouts to a French Drain makes the Drainage System work better.

French Drain Pipe running to curb outlet in Oklahoma City.
French Drain Pipe running to curb outlet in Oklahoma City.
Drainage System Installation in Norman
Drainage System Installation in Norman

French Drains, French Drains, French Drains,  Yes we install French Drains!

Oklahoma Drainage and Sprinkler Repair Servicing Central and Western Oklahoma since 1993. 

We also Install Surface Drains, which make up 6 inch, 9 inch and 12 inch basins. 

We install Channel Drains Across Driveways and Sidewalks.

We Install Sump Pumps to solve difficult drainage issues as well.

Harsh weather in Oklahoma seems to becoming more common.  In 2013,  Norman Oklahoma had 4 inches of rain in two hours.  That’s the most rain in a short time that I can remember.  Storm-Water runoff can cause damage to all types of property and buildings.  Water getting inside your house is never a good thing.  A Drainage System that utilizes a French Drain can help.

Drains can protect your home and property from water damage.  Oklahoma Drainage install a wide variety of Drains in many different places.  A Drain or Group of Drains with Drain Pipe going to an exit point is a “Drainage System.”

A “French Drain” Moves “surface water” away from a low lying problem drainage area.  Sub surface water is many times not considered or thought about when a drainage system is being installed.  People only think about what they can see and don’t think much about what they can’t see.

Sub Surface water is water that is underground and saturated in the soil.  Just like water above ground (Surface Water) moves.  Water under ground moves too and is a very big part of any drainage problem.

Water flows over the surface into the area that floods and is a problem.  A big mistake that is made be the casual eye, is that all the water in a swampy problem area got there by running over the surface.  Yes, it probably did, but it also got there by moving there underground as well.  This is called SUB SURFACE WATER MOVEMENT, and it is important to any kind of Drainage System that might be installed.

If your problem water is partially Sub-Surface water, and you install a Drainage System that uses Surface Drains only, then you just wasted a lot of money!

Surface Drain install
Surface Drain Installed by sidewalk

Water can only be drained away that is on the surface.  It goes into the top of the Drain on the Surface.  It’s Name is ” A Surface Drain.”  It Drains Surface Water ONLY!

A French Drain can drain Surface water and Sub Surface water both.  It water is in the problem area by means of Sub – Surface movement, then it will enter the French Drain Laterally, under ground,  and be drained away along with the surface water.

New French Drain
French Drain with very little fall

Surface Drains look nice but they have limited applications.  They must be installed in situations that they are designed for.  Surface Water only in smaller volume applications.  Surface Drains don’t move as much water as French DrainLarge 6 Inch French Drain Installed in Norman

Drainage Systems can be made up of one drain or a combination of many drains.  Drainage  problems can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together.  Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together.

An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional Surface Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street.

A simple Drainage System might consist of a Surface Drain that is connected to a second Surface Drain which runs to a Pop-up Emitter which lets water drain over the curb and into the street.

An “Exit Point” is the term used for where all the water leaves the Drainage System.  Determining the Exit Point is very critical.  It is one of the first things we do when diagnosing a Drainage Problem.

Drainage Systems can:

1.  Keep water away from foundations — A French Drain is best because it can move Surface Water and Sub-Surface Water (water moving under ground) away from the foundation.  Many times less experienced companies install Surface Drains to keep water away from foundations.  This can be a big mistake.  A Surface Drain can’t move or drain Sub-Surface Water.   Also A Surface Drain often can’t move enough water fast enough and easily becomes overwhelmed during a heavy rain.  A Surface Drain also can’t cover or protect a broad enough area. Surface Drains should be designed in a Drainage System to be located in smaller Drainage Areas moving moderate amounts of water.  Surface Drains look better than French Drains.  If ,”appearance” is more important than Drainage Capacity, Go with the Surface Drain.  Just know what you are getting into and what your expectations should be. One side of a foundation alone,  can be over 100 feet.  A 4 inch or 6 inch French Drain is best when protecting a large area such as a foundation.Surface Drain Installed next to sidewalk in Oklahoma City.

2.  Keep water away from small or enclosed areas.  This might be a low area just through a gate on the side of a house, or the low area between a flowerbed and the wall of a house, or standing water on or near a sidewalk or driveway.  These types of Drainage Problems are best served with Surface Drains.  A Surface Drain can move water away from a low area that is relatively small.  This can occur in yards, flowerbeds, sidewalks and driveways.  A Surface Drain is designed to move Surface Water away from a problem area to a predetermined exit point.  Surface Drains are available in many sizes.  How quickly they remove standing water is usually determined by the size of the Drain Pipe that is connected to the Drain.Surface Drain Installation in Norman

Simply put, a Drainage System is one or a group of underground Drain Pipes that take water away from a place that has water standing on it or flowing across it.  The water that is in the problem area, can be causing damage or may be inconvenient or both.  (Usually Both)  A simple Drainage System is a Drain for the water to enter, a Drain Pipe to move the water away from the Drain, and an Exit Point for the water to be released out of the Drain Pipe.

Drainage Systems quickly can become more complicated.  Considerations must include:

How does the water get to the problem area?  There may be one or many sources.

Water Sources:

1.  It falls from the sky directly

2.  It flows down hill over the surface (surface water)

3.  It flows underground under the surface (sub-surface water)

4.  It flows from the edge of a roof ( There may be many roofs near the problem area, neighbors etc.)

5.  It flows from a gutter downspout

6.  It flows over the edge of a gutter because the gutter is too small is is clogged

7.  It flows up from the ground (seeps and springs are common in Oklahoma)

8.  It flows from a sprinkler system use ( yours or your neighbors)

9.  It flows from a leaking pipe ( water mains, water meters, water lines, sprinkler pipes, sprinkler valves)

There are other reasons for Drainage Problems, the above reasons are just the most common.

Once the number of water sources is determined, a rough estimate of the amount of water that needs to be drained away on average must be estimated.  This can be simplified down to “SMALL, MEDIUM, OR LARGE AMOUNTS OF WATER TO BE DRAINED AWAY.  You don’t have to be an engineer trying to calculate fluid dynamics.  Experience at diagnosing drainage problems helps however.  How much water needs to be moved will help determine the type and size of the Surface Drain or French Drain that needs to be installed.  It also helps to determine the size of Drain Pipe required for the Drainage System.  A good rule to follow is, “If in doubt, install a larger Drain and Drain Pipe.”  Unused Drainage Capacity is better than property damage caused by a Drain that is overwhelmed by too much water.

For home and small business use typical materials used are:

6 inch, 9 inch, and 12 inch Surface Drains

3 inch, 4 inch, and 6 inch Drain Pipes

3 inch, 4 inch, and 6 inch French Drains

French Drains move more water than Surface Drains —

French Drains move Surface Water and Sub-Surface Water

Surface Drains move Surface Water only

Surface Drains look nicer than French Drains in most cases

Once the type and number of drains is determined and what size Drain Pipe will connect them, an exit point must be selected.  (Where is the Drainage System going to take the water to and release it?)

The Drainage Curb Fitting is installed when the desired exit point for the French Drain will release the Drainage Water into the Street.   The Drainage Curb Fitting is rectangular in shape and made to be installed through the curb.  A small section of Curb is cut out with a concrete saw.  The Section is a few inches wider than the Drainage Curb Fitting.  We then install new concrete around the curb fitting.  Once the concrete has dried, the Drain Pipe coming from a French Drain or Surface Drain is connected to the Drainage Curb fitting and then covered with dirt.Cutting The Curb and Installing Curb Fitting for French Drain

The Drainage Pop-Up Emitter is connected to the end of a Drain Pipe.  It is downhill from a French Drain or a Surface Drain.  It is a small release basin with a green pop-up lid.  When releasing water, it pops up about an inch to release the water from the French Drain or Surface Drain.  When the Storm Water has moved through the Drainage System and out of the Pop-Up Emitter, the green lid closes back to its original closed position.  The emitter is designed to release water out into a yard or down a hill or other desirable Drainage Exit Point where there is no curb.Popup Emitter to release water from a Drainage System in Yukon.


Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.

channel drain driveway
Channel Drain set in Driveway

FRENCH DRAIN IN EDMOND OKLAHOMA, 

Surface Drain set in concrete

Drainage System Trench

Drainage System Trench

Oklahoma Drainage and Sprinkler RepairFrench Drain Installation, Drainage System Design, Expert Lawn Sprinkler RepairDrain Repair 

Recently Oklahoma Drainage and Sprinkler Repair installed a large 6 inch French Drain in Edmond.  The customer had water running under his back porch step and into his basement.  We did a Free Drainage Diagnostic and Estimate.  The French Drain design that we proposed would intercept the surface water and subsurface water that was flowing under the steps.  The French Drain design called for a 6 inch French Drain to be installed above and several feet away from the steps.  It would run around the house parallel to the foundation and about 5 feet to the East.  The French Drain would run past the steps to a point where water must cross the French Drain or run up hill to the steps which in this case was not possible.  Once past the steps, the French Drain would transition to Solid 6 inch Drain Pipe and continue on around the house to the Pop-Up Emitter down hill in the side yard.  Along the way we attached several Gutter Down Spoutsinto the French Drain.

Channel Drain in Oklahoma City
Channel Drain in Oklahoma City
Setting in the channel drain
Setting in the Channel Drain in the cut.
Curb Outlet for French Drain in Edmond
Curb Outlet for French Drain in Edmond

French Drain Installation

Oklahoma Drainage and Sprinkler Repair has been diagnosing and solving Drainage Problems since 1993.  Water has the ability to get into places around your home where you really don’t want it to be.  Some drainage problems are easy to solve.  Typically water enters the problem drainage area one way from one source.  The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources.  Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.

An example of this occurs when water is running into a problem area in an obvious way over the ground where you can see it.

Simple enough.

driveway channel drain
Driveway Channel Drain Installation

A drainage system is installed with a surface drain as the “intake” with drainage pipe running to an exit point.  Initially the water drains away and everything looks great.  The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area.  The primary water source was solved, ( The surface water run off ) but the secondary water source was not.  Which was sub-surface water, (ground water) running into the area.  A surface drain can’t drain “ground water.”  A French Drain should have initially been installed instead of a Surface Drain.  A French Drain can drain both Surface Water and Ground Water.

river rock french drain install
A French Drain Can Handle Standing Water

FRENCH DRAIN IN EDMOND OKLAHOMA, DRAINAGE CONTRACTOR

Oklahoma Drainage and Sprinkler Repair Recently installed a large 6 inch French Drain in Edmond.  The customer had water running under his back porch step and into his basement.  We did a Free Drainage Diagnostic and Estimate.  The French Drain design that we proposed would intercept the surface water and subsurface water that was flowing under the steps.  The French Drain design called for a 6 inch French Drain to be installed above and several feet away from the steps.  It would run around the house parallel to the foundation and about 5 feet to the East.  The French Drain would run past the steps to a point where water must cross the French Drain or run up hill to the steps which in this case was not possible.  Once past the steps, the French Drain would transition to Solid 6 inch Drain Pipe and continue on around the house to the Pop-Up Emitter down hill in the side yard.  Along the way we attached several Gutter Down Spouts into the French Drain.

French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain

We solve residential and commercial drainage problems.
We Install lawn Sprinkler Systems.
We repair and redesign Sprinkler Systems.

After a thunder storm, do you have water standing on your driveway, sidewalk, on the side of your house, backyard, front yard, or worst of all — seeping into your home? We can help! We can diagnose your problem and design a drainage system specifically for your needs. We install: French Drains, Surface Drains, Channel Drains, Trench Drains, Basin Drains, Basement Drains, and Sump Pumps.


Oklahoma Drainage and Sprinkler Repair 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

    Sprinkler Repair for all aspects of Residential Sprinkler Systems

    Emergency Sprinkler Repair Service, AFTER HOURS AND WEEKENDS.

Oklahoma Drainage and Sprinkler Repair Installs Surface Drains and French Drains.  Some times it is up hill in all directions from the Problem Drainage Area.  This problem can be solved by installing a Sump Pump.  When the cavity fills, the water is pumped away to the point where the water exits the drain which can be a curb outlet or a pop-up emitter.

Sump Pump Installation
Sump Pump Installation

 

new curb outlet

Curb outlet with more than 6 inches of fall

French Drain Running Through Low Areas

French Drain with stepping stones

WHAT SIZE DRAIN PIPE FOR FRENCH DRAINS?

French Drains can be decorated with many types of stone
French Drains can be decorated with many types of stone

French Drains can utilize  several types and sizes of French Drain Pipe.  An older type that is not commonly used any more is 4 inch PVC Pipe with large half inch holes drilled in the Pipe.  This doesn’t work very well,   Because the holes are too large and the number of holes in the French Drain Pipe are too few.  Also there is no filter or “Soc” around this particular French Drain Pipe.  If it is used in sandy or loose soil the holes will clog and the pipe will fill up with sand.  PVC French Drain Pipe should be avoided.

ADS French Drain Pipe is much better, the holes are smaller and much more numerous.  It also comes inside a soc that acts as a filter and helps keep sand and debris out of the French Drain Pipe.  It works very well.

French Drain in flowerbed
French Drain in flowerbed

For Small business and Residential French Drains, Four inch ADS Perf/Soc French Drain pipe is adequate and the most common.  It is used for the majority of all French Drains installed.  French Drains can be installed using 3 inch ADS Perf/Soc but many times it is too small and can be overwhelmed by a heavy rain or from a bad design.  (Too many gutter down spouts connected directly into the French Drain, For Example)  Three Inch French Drain Pipe should be avoided if possible.

Six inch  ADS Perf/Soc French Drain Pipe is usually a good idea when possible.  It carries a much larger volume of water.  Six Inch French Drains are rarely overwhelmed.

Installing Gravel on top of a 6 inch French Drain
Installing Gravel on top of a 6 inch French Drain

French Drain Installation

Oklahoma Drainage and Sprinkler Repair has been diagnosing and solving Drainage Problems since 1993.  Water has the ability to get into places around your home where you really don’t want it to be.  Some drainage problems are easy to solve.  Typically water enters the problem drainage area one way from one source.  The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources.  Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.

An example of this occurs when water is running into a problem area in an obvious way over the ground where you can see it.

Simple enough.

decorative french drain

French Drains can be decorated with many types of stone

A drainage system is installed with a surface drain as the “intake” with drainage pipe running to an exit point.  Initially the water drains away and everything looks great.  The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area.  The primary water source was solved, ( The surface water run off ) but the secondary water source was not.  Which was sub-surface water, (ground water) running into the area.  A surface drain can’t drain “ground water.”  A French Drain should have initially been installed instead of a Surface Drain.  A French Drain can drain both Surface Water and Ground Water.

 

A French Drain Can Handle Standing Water

 

Oklahoma Drainage and Sprinkler Repair Services all of Central Oklahoma including: Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.

 

 

 

Oklahoma Drainage and Sprinkler Repair Recently installed a Drainage System in Nichols Hills.  The Drainage System was made up of a 4 inch French Drain starting in the back yard.  It ran between the garage and the pool.  Several gutters were connected directly into the French Drain.  From this point, we expanded up to a larger 6 inch Drain pipe to handle the added water into the system from the gutters.  In several places the French Drain had to run through areas where Sprinkler Pipes were in the way.  We had to re-rout all the Sprinkler Pipes and Wires under the French Drain.

French Drain Installed in Yukon

Once the Sprinkler System had been redesigned and the gutters had been connected, we ran the 6 inch Drain Pipe from the end of the French Drain, around the house to release through the curb.  We cut the curb and installed a 6 inch curb fitting with acrylic concrete.  A few days later a major thunderstorm poured down on the property.  The French Drain and the Drainage System Worked Perfectly. This week we installed a 6 Inch French Drain in Oklahoma City.  Water was running down the hill, under the back fence, into the back yard, across the sidewalk, and into the side door going into the garage.  After every heavy rain, water was getting into the garage.  We installed a 6 Inch French Drain across the back yard to divert the water.  We also connected the Gutter Down Spouts Directly into the French Drain.  Once the French Drain was down hill from the house, we changed from French Drain Pipe to solid 6 inch ADS Drain Pipe and continued across the front yard to the street.  Once at the curb, we cut the curb with a concrete saw and installed a Curb Outlet for the French Drain.  Problem solved!

drain install

Installing French Drain in standing water

Something to think about — Most people see and deal with what is obvious when it comes to Drainage Problems.  Surface Water is “Obvious”!  People see it washing over the surface into the area that collects the water.  Simple enough.

A good place for a French Drain

Water Standing in your yard can be tricky. Designing a Drainage System to intercept the Surface Water is the first step, but many times is not the only step.  Often Sub-Surface Water( Water Running Under Ground ) is not accounted for by people with less experience in designing Drainage Systems.  They install A Drainage System that uses Surface Drains to Intercept the running surface water.  Sometimes that works if that is the only water source to the Problem Drainage Area. Surface Drains drain surface water away only.  Sub Surface water runs right around them and into the same Problem Drainage Area.  There may be less water there than there was before but the problem still remains. A French Drain is the solution when water is running into a problem area over the surface and under ground.  A French Drain solves both problems and the area will be dry.

cnannel drain location

Water standing on Driveway, a channel drain is needed.

cutting concrete for channel drain

A Channel Drain is a type of Surface Drain and many times is installed in concrete across sidewalks or driveways.  It is long and narrow with a grate on top.

Installing Channel Drain Across Sidewalk in Norman
Installing Channel Drain Across Sidewalk in Norman

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench.  A  Trench Liner is sometimes used depending on the Drainage System Design and the type of soil.   The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe.   This is to ensure that the Drain Pipe does not become clogged. A trench is dug that is slightly wider than the French Drain Pipe that is being used.  There are several sizes of French Drain Pipe.   Three Inch, Four Inch, and Six Inch are the most common sizes of French drain Pipe. The dirt that is taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed.