Posts Tagged ‘Norman Oklahoma Sprinkler Repair’


Sprinkler Repair –

Spring is here!  Do you have a Sprinkler head that does this?

 

 

Maybe your Sprinkler Valves look like this!  Yikes!

You might want a Sprinkler Head Moved, Replaced, or adjusted.

Things can look nice when your sprinkler heads spray in the right places.

Sprinkler Heads need lots of attention when you have a sprinkler system.   Sometimes a Sprinkler Head needs to be moved.  Landscaping changes, bad original sprinkler head placement, or you just want to move it.  Oklahoma Drainage and Sprinkler Repair can help.

Sprinkler Heads can Freeze and break in the winter time if your sprinkler runs at a bad time or if In-line sprinkler pipe drains were not installed originally.  Dogs like to chew on them and dig them up. Sprinkler Heads get broken when a car or truck is driven across the yard.  But, the majority of sprinkler head damage is done by weed eaters and lawn mowers.

Oklahoma Drainage and Sprinkler Repair has been fixing broken sprinkler heads since 1993.  If you need a sprinkler head fixed, replaced, adjusted, or moved, we can help.

 

 

Sprinkler RepairLeaking Sprinkler Pipes, Broken Sprinkler Heads, Back-Flow Valve Problems, Moving Sprinkler Heads, Adjusting Sprinkler Heads, Sprinkler Wire Problems, Controller Programming Trouble, Sprinkler Valve Problems.  We do it all.

Oklahoma Drainage and Sprinkler Repair 405 203 9419

 

Oklahoma Drainage and Sprinkler Repair provides Emergency Sprinkler Repair Service, After Hours and Weekends.  405 203 9419

Sprinkler Repair is an ongoing issue for any sprinkler system.  Folks in Central Oklahoma are turning on their Sprinkler Systems and discovering problems.    We fixed several leaks in a Sprinkler System in Edmond.  The sprinkler pipes were leaking in several places.  Each leak had to be cut out and replaced.  The Sprinkler System was fairly new.  It was installed last summer by a Pool Company that also installs cheap sprinkler systems. All the joints in the sprinkler pipes were glued together with clear PVC Cement.  That part is OK, But they cut some corners and didn’t use PVC Primer with the glue.  As a result the joints didn’t bond very well and many of them blew apart this spring when the sprinkler systems was turned on.  (Thus all the leaks)  I suspect we will have to go back several times to fix additional leaks.  We can only warranty the PVC joints that we have replaced.   Cheaper isn’t always better.

Recently we fixed a sprinkler system that was poorly installed.

  The Sprinkler System Company that installed it didn’t know what they were doing.  There was no Master Valve installed in the Sprinkler System.  As a result, The Sprinkler Pipe between the water meter and the Sprinkler Valves stayed pressurized all the time.  This is bad during a cold snap in Oklahoma.  If a Master Valve and In-Line Pipe Drains had been installed originally, there would be no broken pipes when it got too cold.    The Sprinkler Pipes would drain automatically.

 


Sprinkler System Repair – We provide service for- Broken Sprinkler Heads — Sprinkler Controllers — Sprinkler ValvesLeaking Sprinkler Pipes — All Brands

Servicing:  All of Central and Western Oklahoma

Sprinkler Repair is an ongoing issue for any sprinkler system.  Folks in Central Oklahoma are turning on their Sprinkler Systems and discovering problems.    We fixed several leaks in a Sprinkler System in Edmond.  The sprinkler pipes were leaking in several places.  Each leak had to be cut out and replaced.  The Sprinkler System was fairly new.  It was installed last summer by a Pool Company that also installs cheap sprinkler systems. All the joints in the sprinkler pipes were glued together with clear PVC Cement.  That part is OK, But they cut some corners and didn’t use PVC Primer with the glue.  As a result the joints didn’t bond very well and many of them blew apart this spring when the sprinkler systems was turned on.  (Thus all the leaks)  I suspect we will have to go back several times to fix additional leaks.  We can only warranty the PVC joints that we have replaced.   Cheaper isn’t always better.

Mustang Oklahoma Sprinkler Repair

Recently we had a customer in Mustang who needed a wiring problem solved for their sprinkler controller.  Several of the sprinkler zones were not working.  We had to trace the sprinkler wires in the yard till we found the problem.  Tracing sprinkler wire is a very difficult Sprinkler Repair to complete.  The Sprinkler Wire is burred which makes the wiring problem hard to find.  It took us a while but we found the problem.  The customer had cable installed and the cable company cut the sprinkler wires.

 

Controller install

Sprinkler Controller Installation

Sprinkler Controller in Mustang 

 

 

 

 If your Sprinkler System has:

1. Broken Sprinkler Heads

2. Leaking Sprinkler Valves

3. Broken Back-Flow Valve

4. Broken Sprinkler Pipes

5.  Defective Sprinkler Clock or Controller

Lawn Irrigation Systems require maintenance from time to time.  All types of Sprinkler Repair become necessary.    Sprinkler heads break for several reasons.  Dogs chew up Sprinkler Heads.  Tree roots twist and break Sprinkler heads.  Cars run over and break Sprinkler Heads.  Weed Eaters cut the tops off Sprinkler Heads.  If you have a Sprinkler Head that is not performing perfectly, We can help.

Sprinkler Valves can have trouble too.  The Sprinkler Valve Wiring becomes disconnected or shorts out.  Tree Roots can stretch or break the Sprinkler WiresSprinkler Valves can start leaking over time. Oklahoma Drainage and Sprinkler Repair can solve Sprinkler Valve problems of all types.

The Sprinkler Valves that you see above are a mess.  They were leaking and weren’t working correctly.  We replaced the above Sprinkler Valves with the ones you see below.

New Sprinkler Valves installed in Norman

New Sprinkler Valves replacing the old ones shown above.


Moving Sprinkler Valves

Recently we had a Sprinkler Repair Customer in Oklahoma City,  He was wanting to have his landscape company install a new tree in his flowerbed.  The problem was that his Sprinkler Valves were right where he wanted to plant the tree.  The addition problem was that he had several Sprinkler Valves tightly grouped together so they could not be moved individually.  The landscaping company had dug around the valves in an attempt to move them.  It turned into a real mess.  They cracked a pipe in the process and water and dirt mixed to make mud.  Which then was allowed to dry around the valves.  What a mess!

The only option was to replace the Sprinkler Valves and at the same time move them to a new location.

First we had to put together the new valves in a tight setting so they could fit in the new valve box that we would Install the Sprinkler Valves in.

Take a look at the picture above.  You may notice that for some strange reason we left the Sprinkler Valves sitting up on there side.  Actually there is a very important reason to do this.  Once the Sprinkler Valves are glued together with “Hot” Glue,  if the group of valves is just laid flat to dry, you will have a big problem.  The excess glue in the pipes will run up inside the valve and cause damage to the Sprinkler Valve.  When putting fittings on a Sprinkler Valve they must be placed so that excess glue will run away from the valve.

The Sprinkler Valves can have all kinds of problems and may not work at all form the beginning.  Since 1993 I have cut out and replaced literally thousands of Sprinkler Valves that had glue up inside them.  Many “Fly By Night” landscaping companies that also work on Sprinkler Systems make this mistake constantly.  I have even seen experienced Sprinkler Repair Companies make this mistake as well.  They get in a hurry and make mistakes.  They should know better.

After assembling the Sprinkler Valves and moving them to a new location out of the flowerbed, we tested the Sprinkler Valves thoroughly.

Now our Sprinkler Repair customer has a new tree in his flowerbed.

Oklahoma Drainage and Sprinkler Repair has been providing Expert Sprinkler Repair since 1993.  We service all of Central and Western Oklahoma.

 


Sprinkler RepairSprinkler ValvesSprinkler HeadsLeaking Pipes – Everything you might need repaired or adjusted with your sprinkler system.

Oklahoma Drainage and Sprinkler Repair – On the Job since 1993 – Servicing Western and Central Oklahoma

Norman Sprinkler Repair 

Recently we had a customer in Norman who had some trouble with a sprinkler head that was leaking at the base.  There was mulch all around the sprinkler head and when the system ran it blew mulch all over the sidewalk.  This is a typical Sprinkler Repair and occurs quite often.  It took us about 15 minutes to fix.  We also moved several Sprinkler Heads that weren’t in the best places.  Moving sprinkler heads is a common practice for Oklahoma Drainage and Sprinkler Repair.

Oklahoma Drainage and Sprinkler Repair –  Expert Sprinkler Repair for all Residential Lawn Sprinkler Systems

Emergency Service – After hours and Weekends

We service all of Central and Western Oklahoma

Since 1993 we have:

Fixed leaking sprinkler pipes in Edmond

Replaced Sprinkler Valves in Norman

Adjusted Sprinkler Heads In Oklahoma City

Installed A New Back Flow Valve In Lawton 

and over 2000 other Sprinkler Repairs in Central and Western Oklahoma.

broken sprinkler pipe

Broken Sprinkler Head took about an hour to fix.

Sprinkler Repair is an ongoing issue for any sprinkler sy

Moving sprinkler valves also is a service that we provide.  It takes a lot more expertise and experience to move sprinkler valves.  There are many reasons that sprinkler valves and sprinkler heads may need to me moved.  Driveways can be added or new landscaping may be installed.  We can redesign any residential sprinkler system Moving Sprinkler Valves, Sprinkler Heads, Sprinkler Pipes, and Sprinkler Wiring is what it takes.

Just like a home or a car, a Sprinkler System requires repair or adjustment from time to time.  We at Oklahoma Drainage and Sprinkler Repair, take great pride in the Sprinkler Repair Services that we provide.  In almost 27 years of service,We have solved virtually every Sprinkler Repair Problem possible.

 

We solve Sprinkler Repair Problems that other companies can’t handle.  If you live in Oklahoma City and have Broken Sprinkler Heads, or if you live in Norman and have Leaking Sprinkler Valves, or if you live in Edmond and your Sprinkler Controller quit working, give us a call or send us an

Lawn Sprinkler Repair is one of our business focuses.   We can help with:

1. Sprinkler Controller Problems

2. Leaking Back-Flow Valves

3. Leaking Sprinkler Pipes

4.  Shorted or disconnected valve wires

5. Sprinkler Zones or Sprinkler Stations that won’t work

6. Broken Sprinkler Heads

The above are the most common problems that we deal with.

 

 

 

Sprinkler System Repair  Broken Sprinkler Heads — Sprinkler Controllers — Sprinkler Valves — All Brands

Servicing:  Oklahoma City — Norman — Moore — Edmond — Mustang — Yukon — Midwest City — Del City — Blanchard — Newcastle 

AND ALL CENTRAL OKLAHOMA.

Now Servicing Western Oklahoma including Lawton and Altus.

 

 

Fixing Leaking Sprinkler Pipes is a common occurrence for Oklahoma Drainage and Sprinkler Repair.  Most recently we had a service call in Lawton.  We got a call from a lady who had water pouring out from under the edge of her driveway.  After shutting off the water at the back-flow valve, we were able to determine that the leak definitely was coming from the sprinkler system.  A cracked sprinkler pipe was the problem and to make matters worse, the sprinkler pipe ran under the driveway.

Oklahoma Drainage and Sprinkler Repair had the solution.  Instead of trying to fix the broken sprinkler pipe, it was a much better idea to replace the entire pipe.  The Sprinkler Repair took about three hours.

Oklahoma City Sprinkler Repair

Recently we helped some folks with their sprinkler controller.  They had a lightning strike melting their sprinkler controller and all the connecting wires. Changing the Sprinkler Controller took a little time, but the larger problem was changing out all the sprinkler wires that ran underground form the controller to the sprinkler valves.  This part took a while and required quite a bit of attention to detail.

SPRINKLER REPAIR IN OKLAHOMA CITY

The sprinkler valve in the picture was replaced by Oklahoma Drainage and Sprinkler Repair. When the Sprinkler Valves were originally installed, they were not put inside a “Valve Box” to protect them. The company that installed them just dumped dirt on them and got paid and left. The Sprinkler System ran ok for about two years before the sprinkler valves failed. We replaced the valves and added a valve box to protect them so this time the Rain Bird valves should last much longer. If you need help with your sprinkler system, give us a call at 405 203 9419. Oklahoma Drainage and Sprinkler Repair has been solving sprinkler problems since 1993.

Oklahoma Drainage and Sprinkler Repair – 405 203 9419

Do you need Sprinkler Repair?

Winter is a time when a lot can go wrong with a Sprinkler System.   Sprinkler Pipes can freeze and break.  Sprinkler heads can crack or bust.  Above Ground Back-Flow Valves can crack or leak even during a warm winter.  Oklahoma Drainage and Sprinkler Repair can help.  Give us a call at :

Sprinkler Controller Trouble Shooting

Having Installed Several Thousand Sprinkler Systems over the past several years, here are the most common mistakes made by homeowners who are not comfortable with their Sprinkler Controller.

Most Sprinkler Controllers have a knob or a digital touch screen.  Either way, the basic functions are the same.

1.  Sometimes some brands of Sprinkler Controllers won’t work because the ” Time and Date,” have not been set correctly.  If you select time/date and the screen is blank with no time or date then you have a problem.

*******************************************************************************************************************************

2.  The most common reason that a Sprinkler Controller won’t work is because the breaker has been tripped for the electrical plug that the controller is plugged into.  People assume that because the LED screen on the controller has power that the controller is receiving power.  THIS IS NOT THE CASE!!!!!!!!!!!!!!!!  ALL CONTROLLERS HAVE BACKUP BATTERIES IN THEM TO MAINTAIN THE CONTROLLERS PROGRAMMING IF YOUR ELECTRICITY GOES OFF.  THE BREAKER CAN BE TRIPPED TO THE ELECTRICAL OUTLET AND THE DIGITAL DISPLAY WILL STILL RUN OFF THE BATTERY MAKING IT LOOK LIKE IT HAS POWER WHEN IT DOES NOT.

TEST YOUR OUTLET BY CHECKING YOUR BREAKERS OR PLUGGING SOMETHING INTO THE SOCKET SUCH AS A LIGHT OR A POWER TOOL.

********************************************************************************************************************************

Another very common mistake is that people confuse “Start Times,” with “Run Times” on the controller.

A Run Time is how long you program each Sprinkler Zone to run.

(Zone 1  5 minutes, Zone 2 8 minutes, Zone 3 25 minutes and so on.)  You program how long you want each Sprinkler Zone to run.

A Start Time is a time that you set on the controller to start zone one running.  All other zones automatically follow zone one in order lowest to highest.  Zone 2 knows to always follow zone 1 when it is done.  Zone 3 knows to follow Zone 2 and so on.  Let me repeat this.  Start Times are only for zone 1.  Again, a “Start Time,” is a time that you would like your Sprinkler System to come and run through all the zones.

Sprinkler Controllers have the ability to run more than one start time.  This is to allow your entire Sprinkler System to run more than once in a 24 hour period.  You can have a Start Time of 1 PM.  Zone 1 comes on and runs until its programmed time elapses.  Zone 2 automatically comes on next and runs.  Then zone 3 and so on.  You might have a 2nd Start Time several hours later to start and run your entire system again.  (2nd start time at 8 PM)  The Sprinkler System has had plenty of time to run through all the zones when it started at 1 PM.  At 8 PM the controller turns zone 1 on again and all the zones run their programmed amount of time.  THE MISTAKE PEOPLE MAKE IS THINKING THAT YOU MUST PROGRAM A START TIME FOR EACH ZONE. ( YOU CAN NOT PROGRAM A START TIME FOR ZONE 2,3,4 etc.)  This is also apparent by the fact that most Sprinkler Controllers have a limit of 4 start times but can run more zones than 4.  Most Sprinkler Controllers can run 10 zones or more.

What causes a big problem is a when person programs a Start Time at 1Pm.  Thinking incorrectly that they need to program a Start Time for zone 2.  They enter a second Start Time for 1:15pm, and a third start time for zone 3 at 1:30 PM.  So here is what happens.  Say each zone is programmed to run for 10 minutes each.(Run Time)  Zone 1 comes on and runs at 1 PM.  At 1:10 PM Zone 1 stops and zone 2 comes on.  At 1:15 PM the second start time kicks in and tries to turn on zone 1 again while zone 2 has only been running for five minutes and the other subsequent zones have not run at all.  This is called an “Overlapping Start Time.”  With an Overlapping Start Time, Different brands of controllers do different things.  They are all bad regardless.  Some will run zone one over and over and over causing a flood.  Others will not run at all.

Most people only use or need one Start Time.

********************************************************************************************************************************

The “Water Budget Feature,” found on most controllers can cause problems with your Sprinkler Run Times.  Water Budget is a quick way to quickly change all your Run Times for all your zones at once.  Example  —  Out of the box, your new Sprinkler Controller will be set to 100%.  If you program zone 1 to run 10 minutes and zone 2 to run 15 minutes then if your water budget is 100% then that is exactly what they will run.  If you change your water budget from 100% to 200% now zone 1 will run 20 minutes and zone 2 will run 30 minutes and any other zone’s run time will run double of what it was programmed at 100%.  This is a great feature until you accidentally change your water budget to 900% and don’t realize it.  (or 5%)

IF YOUR RUN TIMES ARE RUNNING MORE OR LESS THAN WHAT YOU PROGRAMMED THEM FOR THEN CHECK THE WATER BUDGET.

********************************************************************************************************************************

Some of the older digital Sprinkler Controllers have an “Enter” button.  Any programming you do must be followed by hitting the Enter Button.  If you don’t hit it then programming that you think you keyed in is lost.  This is why the newer controllers don’t have an Enter Button.

 

Oklahoma Drainage and Sprinkler Repair has been solving all types of Sprinkler System Problems since 1993.

We provide:

1.  Sprinkler Valve Problems

2.  Sprinkler Wiring Problems

3.  Sprinkler Controller Problems / Sprinkler Clock Problems

4.  Sprinkler Head Problems

5.  Sprinkler Pipe Problems

6.  Sprinkler Coverage Problems

7.  Sprinkler Redesign Problems for new fences or swimming pools.

 

Many times sprinkler repair needs arise at inconvenient times. Water lines can break in the middle of the night.  Back-Flow Valves Freeze and break at night too.  Sometimes things go wrong when we are away from our homes as well.  Sprinkler Systems coming on at the scheduled times but not shutting off is common and has several possible causes.  Sprinkler Valves can “stick” open while running from lack of water pressure, or is not getting enough electrical current to shut it off from the sprinkler controller, or even a small piece of debris is stuck in the sprinkler valve and won’t allow the sprinkler valve to close.


Oklahoma Drainage and Sprinkler Repair –  Have your seen something like this in your yard?

We service all sprinkler head problems.  If the top of your sprinkler Head has weed eater damage, we can install a new one for you.  If your sprinkler head is working OK but is spraying in the wrong place, we can adjust them too.  If something changes in your yard and a sprinkler head needs to be moved to a better location, it’s no problem.  We have been redesigning sprinkler systems since 1993.  We handle all types of Sprinkler Repair.

Experience counts with sprinkler repair.  It is very easy to waste time and money.  There are many mistakes that can easily avoided.  We recently took over a sprinkler repair in Moore from another sprinkler repair company.  The customer had spent a large amount of money replacing their Sprinkler Valves because nothing was working.  We showed up and discovered that the ground wire in the sprinkler controller had accidentally plugged into the zone one outlet.  It took us 30 seconds to fix the problem.

Oklahoma Drainage and Sprinkler Repair has provided Expert Sprinkler Repair for broken sprinkler heads like the one shown above for over 25 years.

 

 

 

Above ground Back Flow Valves many times have problems.  They easily freeze and break during the winter.  When they break, they leak, and usually its a lot of water.  Oklahoma Drainage and Sprinkler Repair has replaced them since 1993.  We also can provide solutions to keep back flow valves from freezing in the first place.

 

 

Sprinkler Valves are a source of Sprinkler Problems.  Sometimes they stick open and won’t shut off.  Even if you turn off or unplug the sprinkler controller.  Other times a sprinkler valve won’t come when its suppose to.  Oklahoma Drainage and Sprinkler Repair has decades of experience adjusting or replacing sprinkler valves.

 

cracked sprinkler pipe

Broken Sprinkler Head took about an hour to fix.

 

 


Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.

Oklahoma Drainage and Sprinkler Repair – Now Servicing all of Western Oklahoma Including Lawton, Altus, Duncan and Elk City.  We have provided service for Central Oklahoma since 1993.
We solve all types of drainage problems and standing water issues for home or business.  If you have water in your basement or standing on your driveway, we can help.  Oklahoma Drainage and Sprinkler Repair installs many types of Drains including French Drains, Surface Drains, and Channel Drains.  If water is a problem. If it gets into a place that your don’t want in or around your home or Business, give us a call.  Since 1993 we have installed over 2000 French Drains, or Drainage Systems.
Expert Lawn Sprinkler Repair is also a service we provide.  Sprinkler Valves, Sprinkler Heads, Sprinkler Controllers, Leaks, Wiring, We service it all.

 

French Drain Running Through Low Areas

French Drain with stepping stones

WHAT SIZE DRAIN PIPE FOR FRENCH DRAINS?

French Drains can be decorated with many types of stone

French Drains can be decorated with many types of stone

French Drains can utilize  several types and sizes of French Drain Pipe.  An older type that is not commonly used any more is 4 inch PVC Pipe with large half inch holes drilled in the Pipe.  This doesn’t work very well,   Because the holes are too large and the number of holes in the French Drain Pipe are too few.  Also there is no filter or “Soc” around this particular French Drain Pipe.  If it is used in sandy or loose soil the holes will clog and the pipe will fill up with sand.  PVC French Drain Pipe should be avoided.

ADS French Drain Pipe is much better, the holes are smaller and much more numerous.  It also comes inside a soc that acts as a filter and helps keep sand and debris out of the French Drain Pipe.  It works very well.

 

 

 

French Drain Pipe running to curb outlet in Oklahoma City.

French Drain Pipe running to curb outlet in Oklahoma City.

 

 

 

The sprinkler controller seen below was installed in east Norman in 2007.

 

Lawn Sprinkler Repair is one of our business focuses.   We can help with:

1. Sprinkler Controller Problems

2. Leaking Back-Flow Valves

3. Leaking Sprinkler Pipes

4.  Shorted or disconnected valve wires

5. Sprinkler Zones or Sprinkler Stations that won’t work

6. Broken Sprinkler Heads

The above are the most common problems that we deal with.

can help if you need to re-design your sprinkler system. If for example you are adding a swimming pool in your back yard, we can move the sprinkler heads and sprinkler pipes to fit the new dimensions of your yard. We can redesign or add-on to sprinkler systems where the home owners needs change.

– Adjustment of  a Sprinkler System is a necessary part of owning and operating an Irrigation System Sprinkler Heads get run over by cars or get knocked out of adjustment by weed-eaters. Sprinkler Heads need to be moved or adjusted for many reasons.  If your Sprinklers are not putting water where it needs to go, give us a call.

Just what is a “French Drain?”  Many times people incorrectly

use the phrase, “French Drain,”  to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drain Pipe is connected underground to an outlet on the Drain Basin Storm-Water Drains through the grate into the Drain Basin.  Once in the Drain Basin, water travels out of the basin through a Drain Pipe.  The Storm-Water continues downhill in an underground Drain Pipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

A Channel Drain is a type of Surface Drain and many times is installed in concrete across sidewalks or driveways.

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench.  The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe.   This is to ensure that the Drain Pipe does not become clogged.

The dirt that was taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed.

A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.
The main downfall of a French Drain is that they, for the most part aren’t very pretty.  They don’t look very nice in a yard once they are completed.
Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the lime stone.  Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel.  This is Ok.  It won’t have a measurable effect on the performance of the drain.
DONT COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT.  THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT.  DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.

DECORATIVE STONE CAN BE USED TO COVER A FRENCH DRAIN AND THEY LOOK GREAT AND LAST A LIFETIME.

French Drains Can Look Great!

 


Sprinkler RepairLeaking Sprinkler Pipes, Broken Sprinkler Heads, Back-Flow Valve Problems, Moving Sprinkler Heads, Adjusting Sprinkler Heads, Sprinkler Wire Problems, Controller Programming Trouble, Sprinkler Valve Problems.  We do it all.

Oklahoma Drainage and Sprinkler Repair 405 203 9419

 

Oklahoma Drainage and Sprinkler Repair provides Emergency Sprinkler Repair Service, After Hours and Weekends.  405 203 9419

Sprinkler Repair is an ongoing issue for any sprinkler system.  Folks in Central Oklahoma are turning on their Sprinkler Systems and discovering problems.    We fixed several leaks in a Sprinkler System in Edmond.  The sprinkler pipes were leaking in several places.  Each leak had to be cut out and replaced.  The Sprinkler System was fairly new.  It was installed last summer by a Pool Company that also installs cheap sprinkler systems. All the joints in the sprinkler pipes were glued together with clear PVC Cement.  That part is OK, But they cut some corners and didn’t use PVC Primer with the glue.  As a result the joints didn’t bond very well and many of them blew apart this spring when the sprinkler systems was turned on.  (Thus all the leaks)  I suspect we will have to go back several times to fix additional leaks.  We can only warranty the PVC joints that we have replaced.   Cheaper isn’t always better.

Broken Sprinkler Head took about an hour to fix.

Today we did a sprinkler repair in Norman.  The sprinkler system needed a checkup.  We went through each sprinkler zone and identified several different problems.  Zone 2 had a cracked sprinkler pipe in a flower bed.  Zone 4 had a broken sprinkler rotor on the edge of the driveway that had been driven over and broken.  Zone 6 and 7 each had a couple of pop-up spray heads that were worn out and would not pop-up.  The diagnosis and the repair took less than two hours.  Now their  sprinkler system is running great!

Recently we fixed a sprinkler system that was poorly installed.

  The Sprinkler System Company that installed it didn’t know what they were doing.  There was no Master Valve installed in the Sprinkler System.  As a result, The Sprinkler Pipe between the water meter and the Sprinkler Valves stayed pressurized all the time.  This is bad during a cold snap in Oklahoma.  If a Master Valve and In-Line Pipe Drains had been installed originally, there would be no broken sprinkler pipes when it got too cold.    The Sprinkler Pipes would drain automatically.
Oklahoma Drainage and Sprinkler Repair also installs French Drains and Drainage Systems

If you live in Oklahoma City and need a French Drain installed in your yard, or along your driveway, or near your foundation, give us a call.  If you live in Edmond or Norman and need a Surface Drain installed in the concrete in your sidewalk or driveway, we can help.  If you live in Mustang or Yukon and would like to protect your trees or flower beds from standing water with a French Drain,Oklahoma Drainage and Sprinkler Repair specializes in just that!

Emergency Sprinkler Repair Service — — Drainage SystemsFrench Drains Surface DrainsSump Pumps  Scheduled Sprinkler Repair

Servicing all of Central and Western Oklahoma

Spring is just around the corner.  Now is a good time to consider a Sprinkler System Checkup by Oklahoma Drainage and Sprinkler Repair.   We have been in business since 1993.

  Drainage Systems for Home owners and businesses including:  French Drains, Surface Drains, Channel Drains, Trench Drains, Basement Drains, Basin Drains, and Sump Pumps.

 


This week Oklahoma Drainage and Sprinkler Repair overhauled a flowerbed Sprinkler Zone in a Sprinkler System in East Norman.  The homeowner had an existing Sprinkler System that was in good shape for the most part, but had problems with the flowerbed Sprinkler Zone.  It had a Drip Sprinkler Zone installed.  The Drip Sprinkler System was installed correctly but was not practical for the flower bed.  The flowerbed was very sandy and could not retain water very well even with good mulch.  Plus the surrounding brick walls increased the amount of heat the plants had to endure in the summer.  The Drip Sprinkler Zone could not provide enough water fast enough for the plants.

We provide:

1.  Sprinkler Valve Problems

2.  Sprinkler Wiring Problems

3.  Sprinkler Controller Problems / Sprinkler Clock Problems

4.  Sprinkler Head Problems

5.  Sprinkler Pipe Problems

6.  Sprinkler Coverage Problems

7.  Sprinkler Redesign Problems for new fences or swimming pools.

If you have water running down the street in the middle of the night because your sprinkler system is leaking or won’t shut off, give Oklahoma Drainage and Sprinkler Repair a call.  405 203 9419

 

Broken Sprinkler Head took about an hour to fix.

Sprinkler Repair is a central focus for Oklahoma Drainage and Sprinkler Repair.  Just like any car or home, a lawn sprinkler system must be updated and maintained.  Typically people wait till spring to get the kinks worked out of their sprinkler system.

 

I can tell you this, DON’T WAIT TILL MARCH TO GET YOUR SPRINKLER SYSTEM IN SHAPE.  BY APRIL THERE WILL BE A  FLOOD OF PEOPLE TRYING TO GET BROKEN SPRINKLER HEADS FIXED OR NEW SPRINKLER CONTROLLERS INSTALLED OR LEAKING BACK-FLOW VALVES REPLACED.

CONSIDER GETTING YOUR SPRINKLER REPAIR WORK DONE ANY TIME OTHER THAN THE SPRING.  FOR THOSE OF YOU WHO HAVE NO CHOICE AND MUST HAVE WORK DONE IN THE SPRING, SCHEDULE AS EARLY AS YOU CAN.

OUR SPRINKLER REPAIR WORK IS TOP QUALITY AND OUR PRICES ARE FAIR.  IT IS OUR GOAL TO GET TO CUSTOMERS QUICKLY IN MARCH AND APRIL, WHILE MAINTAINING OUR QUALITY OF WORK.

Oklahoma drainage and Sprinkler Repair can help with:

1.  Sprinkler Controller Problems

2.  Leaking Back-Flow Valves

3.  Leaking Sprinkler Pipes

4.  Shorted or disconnected Sprinkler Valve Wires

5. Sprinkler Zones or Sprinkler Stations that won’t work

6. Broken Sprinkler Heads

7.  Sprinkler Head Adjustment

The Sprinkler System Problems listed above are the most common Sprinkler Problems that we deal with.

Oklahoma Drainage and Sprinkler Repair  can help if you need to re-design your Sprinkler System.  If for example you are adding a swimming pool in your back yard, we can move the Sprinkler Heads and Sprinkler Pipes to fit the new dimensions of your yard.  We can redesign or add-on to sprinkler systems where the home owners needs change.

Maybe you don’t need a large part of your sprinkler system redesigned.  You May just want a few heads moved to new locations.

What ever your Sprinkler needs may be, Oklahoma Drainage and Sprinkler Repair can help.  Give us a call at : 405 203 9419

 


Norman Oklahoma Sprinkler Repair

 

Oklahoma Drainage and Sprinkler Repair had a call from a Norman Resident.  She had a trash truck back up into her yard.  Unfortunately it was right on top of a rotor sprinkler head.  The Sprinkler Head was crushed as well as the sprinkler pipe underneath.  Water was pouring down the street when the sprinkler system ran.

While we were running the sprinkler system we found that a sprinkler valve was sticking as well.  The one of the sprinkler zones was not shutting off.   So now we had two Sprinkler Repairs to preform.

Fixing the Broken Sprinkler Head and Replacing the broken sprinkler pipe underneath took a little while because the Sprinkler Pipe was up against the curb and the Sprinkler Pipe was hard to get to.  But after getting a little muddy, the Sprinkler Pipe was fixed and the Sprinkler Head was replaced.

 

The Sprinkler Valve that was sticking was much easier to fix.  The bleed screw on the top of the Sprinkler Valve was loose.  It just needed to be tightened.  It only took a few seconds and we did not charge anything for the Sprinkler Repair on the Sprinkler Valve.

Oklahoma Drainage and Sprinkler Repair has been in business since 1993.  During that time we have serviced countless sprinkler systems all over Central and Western Oklahoma.  Give us a call for an estimate 405 203 9419

We also provide Emergency Sprinkler Repair for After Hours and Weekends.

Sprinkler Repair is an ongoing issue for any sprinkler system.  Folks in Central Oklahoma are turning on their Sprinkler Systems and discovering problems.    We fixed several leaks in a Sprinkler System in Edmond.  The sprinkler pipes were leaking in several places.  Each leak had to be cut out and replaced.  The Sprinkler System was fairly new.  It was installed last summer by a Pool Company that also installs cheap sprinkler systems. All the joints in the sprinkler pipes were glued together with clear PVC Cement.  That part is OK, But they cut some corners and didn’t use PVC Primer with the glue.  As a result the joints didn’t bond very well and many of them blew apart this spring when the sprinkler systems was turned on.  (Thus all the leaks)  I suspect we will have to go back several times to fix additional leaks.  We can only warranty the PVC joints that we have replaced.   Cheaper isn’t always better.

Broken Sprinkler Head took about an hour to fix.

Today we did a sprinkler repair in Norman.  The sprinkler system needed a checkup.  We went through each sprinkler zone and identified several different problems.  Zone 2 had a cracked sprinkler pipe in a flower bed.  Zone 4 had a broken sprinkler rotor on the edge of the driveway that had been driven over and broken.  Zone 6 and 7 each had a couple of pop-up spray heads that were worn out and would not pop-up.  The diagnosis and the repair took less than two hours.  Now their  sprinkler system is running great!

Recently we fixed a sprinkler system that was poorly installed.


Oklahoma City Sprinkler Repair

Recently we helped some folks with their sprinkler controller.  They had a lightning strike melting their sprinkler controller and all the connecting wires. Changing the Sprinkler Controller took a little time, but the larger problem was changing out all the sprinkler wires that ran underground form the controller to the sprinkler valves.  This part took a while and required quite a bit of attention to detail.

SPRINKLER REPAIR IN OKLAHOMA CITY

The sprinkler valve in the picture was replaced by Oklahoma Drainage and Sprinkler Repair. When the Sprinkler Valves were originally installed, they were not put inside a “Valve Box” to protect them. The company that installed them just dumped dirt on them and got paid and left. The Sprinkler System ran ok for about two years before the sprinkler valves failed. We replaced the valves and added a valve box to protect them so this time the Rain Bird valves should last much longer. If you need help with your sprinkler system, give us a call at 405 203 9419. Oklahoma Drainage and Sprinkler Repair has been solving sprinkler problems since 1993.

Oklahoma Drainage and Sprinkler Repair – 405 203 9419

Do you need Sprinkler Repair?

Winter is a time when a lot can go wrong with a Sprinkler System.   Sprinkler Pipes can freeze and break.  Sprinkler heads can crack or bust.  Above Ground Back-Flow Valves can crack or leak even during a warm winter.  Oklahoma Drainage and Sprinkler Repair can help.  Give us a call at :

Sprinkler Controller Trouble Shooting

Having Installed Several Thousand Sprinkler Systems over the past several years, here are the most common mistakes made by homeowners who are not comfortable with their Sprinkler Controller.

Most Sprinkler Controllers have a knob or a digital touch screen.  Either way, the basic functions are the same.

Sprinkler Controller with Rain/Freeze Sensor in Oklahoma City

Sprinkler Controller with Rain/Freeze Sensor in Oklahoma City

1.  Sometimes some brands of Sprinkler Controllers won’t work because the ” Time and Date,” have not been set correctly.  If you select time/date and the screen is blank with no time or date then you have a problem.

*******************************************************************************************************************************

2.  The most common reason that a Sprinkler Controller won’t work is because the breaker has been tripped for the electrical plug that the controller is plugged into.  People assume that because the LED screen on the controller has power that the controller is receiving power.  THIS IS NOT THE CASE!!!!!!!!!!!!!!!!  ALL CONTROLLERS HAVE BACKUP BATTERIES IN THEM TO MAINTAIN THE CONTROLLERS PROGRAMMING IF YOUR ELECTRICITY GOES OFF.  THE BREAKER CAN BE TRIPPED TO THE ELECTRICAL OUTLET AND THE DIGITAL DISPLAY WILL STILL RUN OFF THE BATTERY MAKING IT LOOK LIKE IT HAS POWER WHEN IT DOES NOT.

TEST YOUR OUTLET BY CHECKING YOUR BREAKERS OR PLUGGING SOMETHING INTO THE SOCKET SUCH AS A LIGHT OR A POWER TOOL.

********************************************************************************************************************************

Another very common mistake is that people confuse “Start Times,” with “Run Times” on the controller.

A Run Time is how long you program each Sprinkler Zone to run.

(Zone 1  5 minutes, Zone 2 8 minutes, Zone 3 25 minutes and so on.)  You program how long you want each Sprinkler Zone to run.

A Start Time is a time that you set on the controller to start zone one running.  All other zones automatically follow zone one in order lowest to highest.  Zone 2 knows to always follow zone 1 when it is done.  Zone 3 knows to follow Zone 2 and so on.  Let me repeat this.  Start Times are only for zone 1.  Again, a “Start Time,” is a time that you would like your Sprinkler System to come and run through all the zones.

Sprinkler Controllers have the ability to run more than one start time.  This is to allow your entire Sprinkler System to run more than once in a 24 hour period.  You can have a Start Time of 1 PM.  Zone 1 comes on and runs until its programmed time elapses.  Zone 2 automatically comes on next and runs.  Then zone 3 and so on.  You might have a 2nd Start Time several hours later to start and run your entire system again.  (2nd start time at 8 PM)  The Sprinkler System has had plenty of time to run through all the zones when it started at 1 PM.  At 8 PM the controller turns zone 1 on again and all the zones run their programmed amount of time.  THE MISTAKE PEOPLE MAKE IS THINKING THAT YOU MUST PROGRAM A START TIME FOR EACH ZONE. ( YOU CAN NOT PROGRAM A START TIME FOR ZONE 2,3,4 etc.)  This is also apparent by the fact that most Sprinkler Controllers have a limit of 4 start times but can run more zones than 4.  Most Sprinkler Controllers can run 10 zones or more.

What causes a big problem is a when person programs a Start Time at 1Pm.  Thinking incorrectly that they need to program a Start Time for zone 2.  They enter a second Start Time for 1:15pm, and a third start time for zone 3 at 1:30 PM.  So here is what happens.  Say each zone is programmed to run for 10 minutes each.(Run Time)  Zone 1 comes on and runs at 1 PM.  At 1:10 PM Zone 1 stops and zone 2 comes on.  At 1:15 PM the second start time kicks in and tries to turn on zone 1 again while zone 2 has only been running for five minutes and the other subsequent zones have not run at all.  This is called an “Overlapping Start Time.”  With an Overlapping Start Time, Different brands of controllers do different things.  They are all bad regardless.  Some will run zone one over and over and over causing a flood.  Others will not run at all.

Most people only use or need one Start Time.

********************************************************************************************************************************

The “Water Budget Feature,” found on most controllers can cause problems with your Sprinkler Run Times.  Water Budget is a quick way to quickly change all your Run Times for all your zones at once.  Example  —  Out of the box, your new Sprinkler Controller will be set to 100%.  If you program zone 1 to run 10 minutes and zone 2 to run 15 minutes then if your water budget is 100% then that is exactly what they will run.  If you change your water budget from 100% to 200% now zone 1 will run 20 minutes and zone 2 will run 30 minutes and any other zone’s run time will run double of what it was programmed at 100%.  This is a great feature until you accidentally change your water budget to 900% and don’t realize it.  (or 5%)

IF YOUR RUN TIMES ARE RUNNING MORE OR LESS THAN WHAT YOU PROGRAMMED THEM FOR THEN CHECK THE WATER BUDGET.

********************************************************************************************************************************

Some of the older digital Sprinkler Controllers have an “Enter” button.  Any programming you do must be followed by hitting the Enter Button.  If you don’t hit it then programming that you think you keyed in is lost.  This is why the newer controllers don’t have an Enter Button.