Archive for the ‘Moore Oklahoma French Drain’ Category


Oklahoma Drainage and Sprinkler Repair – 405 203-9419

Have you ever had water sanding on your Driveway?  Water on Driveways can cause cement or asphalt to break down and come apart resulting in cracks and deterioration.  Not to mention getting out of your car and stepping into water is never pleasant!

Surface Drain installed in Driveway with Metal Grate.

Oklahoma Drainage and Sprinkler Repair can help by installing a surface drain in your driveway or sidewalk.  If you live in Edmond and need help, give us a call.  We service all of Central and Western Oklahoma.

We install all types of Residential Drains including : French Drains, Surface Drains, and Channel Drains.

Installing Channel Drain Across Sidewalk in Norman

 

These folks had water standing right at there front door.  Installing a Channel Drain solved the problem.


French Drain Installation is what we do!  OKLAHOMA DRAINAGE AND SPRINKLER REPAIR has been installing Drainage Systems in Central Oklahoma for over 27 years.  We solve all types of Drainage Problems for residential and commercial customers.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.

Colored Gravel for a French Drain

French Drain Installation

Oklahoma Drainage and Sprinkler Repair has been diagnosing and solving Drainage Problems since 1993.  Water has the ability to get into places around your home where you really don’t want it to be.  Some drainage problems are easy to solve.  Typically water enters the problem drainage area one way from one source.  The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources.  Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.

An example of this occurs when water is running into a problem area in an obvious way over the ground where you can see it.

Simple enough.

A drainage system is installed with a surface drain as the “intake” with drainage pipe running to an exit point.  Initially the water drains away and everything looks great.  The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area.  The primary water source was solved, ( The surface water run off ) but the secondary water source was not.  Which was sub-surface water, (ground water) running into the area.  A surface drain can’t drain “ground water.”  A French Drain should have initially been installed instead of a Surface Drain.  A French Drain can drain both Surface Water and Ground Water.

 

 

French Drain In Moore with River Rock

 

 

Recently we installed a Drainage System in Moore.  Our customer had a new home.  Originally their home was destroyed in Moore‘s last tornado.  Every time it rains their back yard turns into a pond.

DSC00680

Drain Pipe running from French Drain to the street in Moore

WE installed a 6 inch French Drain in the back yard and connected the gutter down-spouts into the French Drain.  From that point we ran ADS solid Drain Pipe all the way to the street.  At that point the curb was cut and a Curb Outlet was installed with acrylic concrete.  The French Drain did the trick.  Drainage Problem solved.

Some Drainage Systems are complex and incorporate several types of drains.  Most Drainage Systems , however are basic and require just one type of DrainOklahoma Drainage and Sprinkler Repair installs a variety of drains to solve a variety of problems. French Drains, Surface Drains, and Channel Drains are most commonly used.  If you live in Edmond and need a Channel Drain installed across your driveway, or if you live in Norman and need a French Drain in your backyard, or if you live in Oklahoma City and need a Surface drain installed next to your sidewalk, we can help.

Channel Drain Installed by CMG In Yukon

Channel Drain Installed In Yukon

Channel Drains are one kind of Surface Drain that we install in concrete.

Just what is a “French Drain?” Many times people incorrectly

A French Drain can protect your foundation!

use the phrase, “French Drain,” when they mean “Surface Drain” or “Channel Drain.”

A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench. The French Drain Trench runs through a Problem Drainage Area that needs to be drained.   The French Drain Pipe is perforated (Full of Small Holes) and has Neo-Prene Soc around the pipe.  This soc helps prevent debris from clogging the French Drain Pipe.

Perforated French Drain Pipe

The dirt that was taken out to make the trench is hauled away. It is replaced by some type of small stone or gravel depending on what is desired or available. I prefer crushed 1 inch lime stone. It is the most economical option in my area. Pea Gravel or some other type of small stone can work just as well. The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level). In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed. This helps maintain the integrity of the trench over time. It also increases the cost of the French Drain and the amount of time to install it. I install a trench liner in a French Drain about 20% of the time. Most of the time a liner in not needed.

French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations. It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.

French Drain with Colored Gravel

The main downfall of a French Drain is that they, for the most part aren’t very pretty. They don’t look very nice in a yard once they are completed.

Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the lime stone. Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel. This is Ok. It won’t have a measurable effect on the performance of the drain.

DON’T COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT. THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT. DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.

DECORATIVE STONE CAN BE USED TO COVER A FRENCH DRAIN AND THEY LOOK GREAT AND LAST A LIFETIME.

Drainage Systems can be made up of one drain or a combination of many drains.  Drainage  problems can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together. Many times a French Drain, might be connected to a Surface Drain,  which then could be connected to another French Drain.   Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together.

Cutting The Curb and Installing Curb Fitting With Acrylic Cement
Cutting The Curb for French Drain Outlet

An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional French Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street.

A simple Drainage System might consist of a French Drain  which runs to a Pop-up Emitter which lets water drain over the curb and into the street.

An “Exit Point” is the term used for where all the water leaves the Drainage System.  Determining the Exit Point is very critical.  It is one of the first things we do when diagnosing a Drainage Problem.

Drainage Systems can:

1.  Keep water away from foundations — A French Drain is best because it can move Surface Water and Sub-Surface Water (water moving under ground) away from the foundation.  Many times less experienced companies install Surface Drains to keep water away from foundations.  This can be a big mistake.  A Surface Drain can’t move or drain Sub-Surface Water.   Also A Surface Drain often can’t move enough water fast enough and easily becomes overwhelmed during a heavy rain.  A Surface Drain also can’t cover or protect a broad enough area. Surface Drains should be designed in a Drainage System to be located in smaller Drainage Areas moving moderate amounts of water.  Surface Drains look better than French Drains.  If ,”appearance” is more important than Drainage Capacity, Go with the Surface Drain.  Just know what you are getting into and what your expectations should be. One side of a foundation alone,  can be over 100 feet.  A 4 inch or 6 inch French Drain is best when protecting a large area such as a foundation.

2.  Keep water away from small or enclosed areas.  This might be a low area just through a gate on the side of a house, or the low area between a flowerbed and the wall of a house, or standing water on or near a sidewalk or driveway.  These types of Drainage Problems are best served with Surface Drains.  A Surface Drain can move water away from a low area that is relatively small.  This can occur in yards, flowerbeds, sidewalks and driveways.  A surface Drain is designed to move Surface Water away from a problem area to a predetermined exit point.  Surface Drains are available in many sizes.  How quickly they remove standing water is usually determined by the size of the pipe that is connected to the drain.

Simply put, a Drainage System is one or a group of underground Drain Pipes that take water away from a place that has water standing on it or flowing across it.  The water that is in the problem area, can be causing damage or may be inconvenient or both.  (Usually Both)  A simple Drainage System is a Drain for the water to enter, a Drain Pipe to move the water away from the Drain, and an Exit Point for the water to be released out of the Drain Pipe.

Drainage Systems quickly can become more complicated.  Considerations must include:

How does the water get to the problem area?  There may be one or many sources.

Water Sources:

1.  It falls from the sky directly

2.  It flows down hill over the surface (surface water)

3.  It flows underground under the surface (sub-surface water)

4.  It flows from the edge of a roof ( There may be many roofs near the problem area, neighbors etc.)

5.  It flows from a gutter downspout

6.  It flows over the edge of a gutter because the gutter is too small is is clogged

7.  It flows up from the ground (seeps and springs are common in Oklahoma)

8.  It flows from a sprinkler system use ( yours or your neighbors)

9.  It flows from a leaking pipe ( water mains, water meters, water lines, sprinkler pipes, sprinkler valves)

There are other reasons for Drainage Problems, the above reasons are just the most common.

Once the number of water sources is determined, a rough estimate of the amount of water that needs to be drained away on average must be estimated.  This can be simplified down to “SMALL, MEDIUM, OR LARGE AMOUNTS OF WATER TO BE DRAINED AWAY.  You don’t have to be an engineer trying to calculate fluid dynamics.  Experience at diagnosing drainage problems helps however.  How much water needs to be moved will help determine the type and size of the Surface Drain or French Drain that needs to be installed.  It also helps to determine the size of Drain Pipe required for the Drainage System.  A good rule to follow is, “If in doubt, install a larger Drain and Drain Pipe.”  Unused Drainage Capacity is better than property damage caused by a Drain that is overwhelmed by too much water.

For home and small business use typical materials used are:

6 inch, 9 inch, and 12 inch Surface Drains

3 inch, 4 inch, and 6 inch Drain Pipes

3 inch, 4 inch, and 6 inch French Drains

French Drains move more water than Surface Drains —

French Drains move Surface Water and Sub-Surface Water

Surface Drains move Surface Water only

Surface Drains look nicer than French Drains in most cases

Once the type and number of drains is determined and what size Drain Pipe will connect them, an exit point must be selected.  (Where is the Drainage System going to take the water to and release it?)

The Drainage Curb Fitting is installed when the desired exit point for the French Drain will release the Drainage Water into the Street.   The Drainage Curb Fitting is rectangular in shape and made to be installed through the curb.  A small section of Curb is cut out with a concrete saw.  The Section is a few inches wider than the Drainage Curb Fitting.  We then install new concrete around the curb fitting.  Once the concrete has dried, the Drain Pipe coming from a French Drain or Surface Drain is connected to the Drainage Curb fitting and then covered with dirt.

DSC00701

Installing a Curb Outlet for a French Drain


Oklahoma Drainage and Sprinkler Repair – 405 203 9419

We have been solving Drainage Problems since 1993.  We utilize French Drains, Surface Drains, Channel Drains, and even Sump Pumps in our Drainage Systems.

If you have water standing in a bad place, such as a Flower Bed, Basement, Driveway, Sidewalk, or Yard, We can help

 

Today we are installing a French Drain system for a customer in East Norman.  She has water running into her front door through her flower bed.  The bed acts like a pond and over-spills onto her front porch and then through her front door.  To solve the problem, we are installing a French Drain running across her flower bed and under her sidewalk.  Once under the sidewalk the French Drain will connect to Solid Drain Pipe and continue on down the hill to the exit point where we will install a pop-up emitter.  There are two gutter downspouts that will be connected into the French Drain System along the way.

 

French Drain with colored river rock along foundation

French Drain with colored river rock along foundation

 

French Drain Pipe running to curb outlet in Oklahoma City.

French Drain Pipe running to curb outlet in Oklahoma City.

 

 


The term, “French Drain” gets thrown around a lot.  Many times people say they need a “French Drain,” when they mean Surface Drain, or Channel Drain.  It is becoming a Catch-All Phrase that may refer to any type of drain.  French Drains provide specific benefits that are different from Surface Drains.

Just what is a “French Drain?” Many times people incorrectly

French Drain can protect your foundation!

use the phrase, “French Drain,” when they mean “Surface Drain” or “Channel Drain.”

A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench. The French Drain Trench runs through a Problem Drainage Area that needs to be drained.   The French Drain Pipe is perforated (Full of Small Holes) and has Neo-Prene Soc around the pipe.  This soc helps prevent debris from clogging the French Drain Pipe.

Perforated French Drain Pipe

The dirt that was taken out to make the trench is hauled away. It is replaced by some type of small stone or gravel depending on what is desired or available. I prefer crushed 1 inch lime stone. It is the most economical option in my area. Pea Gravel or some other type of small stone can work just as well. The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level). In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed. This helps maintain the integrity of the trench over time. It also increases the cost of the French Drain and the amount of time to install it. I install a trench liner in a French Drain about 20% of the time. Most of the time a liner in not needed.

French Drain March 2011

French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations. It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.

The main downfall of a French Drain is that they, for the most part aren’t very pretty. They don’t look very nice in a yard once they are completed.

Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the lime stone. Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel. This is Ok. It won’t have a measurable effect on the performance of the drain.

French Drain

DONT COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT. THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT. DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.

DECORATIVE STONE CAN BE USED TO COVER A FRENCH DRAIN AND THEY LOOK GREAT AND LAST A LIFETIME.

 

 The French Drain Installation we did this week was a little more difficult than normal.  Many times the route that a Perforated French Drain Pipe must travel to its exit point is not very easy from an installation point of view.  French Drains may have to travel through tree roots, (big ones) under sidewalks, through retaining walls, around swing sets or dog kennels or Mom’s Prize Rose Bush.  The 4 inch French Drain we installed this week was in Oklahoma City south of 23rd in an old part of town where all the houses were old 2 or 3 story homes with lots of huge Elm Trees.  The Elm Tree in Question actually was just an old stump that had been topped out but not completely removed.  They left the roots just for us!  The roots were growing into the homes foundation and were right in the way of the path of the French Drain.  Forty feet of solid Elm Roots and 4 chain-saw blades later We were successful in running a new French Drain through a tree stump.  Yuck! “Well you gotta  do what you gotta do!”

 

French Drain with colored river rock

French Drain with colored river rock

A little info about French Drain Pipe and Tree Roots.  Normally tree roots don’t seek out and penetrate French Drain Pipe.  Tree roots seek moisture and residual water that may stay inside Solid Drain Pipe.  French Drain Pipe is perforated.  Water that does not reach the exit point of the French Drain will seep out of the Pipe into the surrounding dirt.  Solid Drain Pipe that is used with Surface Drains can be penetrated and eventually clogged by roots if the pipe does not have good slope or “Fall”.  If the solid pipe does not drain well and has residual water, tree roots will seek it out.

Drain Pipe running from French Drain to the street in Oklahoma City

Drain Pipe running from French Drain to the street in Oklahoma City

Drainage Systems are designed to protect your home or business from standing water.  Storm-Water Runoff can cause damage in many ways.  Water from your gutters can seep down into your home’s foundation if it has no good way to drain off.  If the temperature then drops below freezing, the water around your foundation can freeze and cause serious damage to the home’s foundation.  Foundation repair can cost more than a Drainage System.

Drainage Systems typically make use of , French Drains, Surface Drains, or Channel Drains.  Depending on the Drainage Problem, A Drainage System may utilize one or several types of DrainsWe might install, for example, A Surface Drain in the middle of a driveway that runs to a gutter that is connected into the drain pipe.  The Drain Pipe might continue to a French Drain running parallel to a homes foundation.  Next the drain pipe might continue to a channel drain cutting across a sidewalk.  The Drain pipe might then reach its exit point running out through a curb fitting installed and cemented through the curb.

A Surface Drain basically is a basin that has a grate on the top.  A drain pipe is connected to the basin below ground.  The water flows in through the grate and down into the basin.  The water then exits the Basin through the Drain Pipe and move toward the exit point of  the Drainage System.  Surface Drains are designed to handle water that accumulates in a low areas.   These areas should not be too large or broad, and the water that drains into a surface drain should not be moving very fast.  Surface Drains can become overwhelmed if they are placed in an area that must move a large volume of water, quickly.  Selecting the correct drain for the specific drainage problem is a benefit that Oklahoma Drainage and Sprinkler Repair provides through twenty years of experience.

 


Drainage Systems, French Drains, Surface Drains, Channel Drains, Sump Pumps, Sprinkler Repair, with 26 years of experience. 

Oklahoma Drainage and Sprinkler Repair Recently installed a Drainage System in Nichols Hills.  The Drainage System was made up of a 4 inch French Drain starting in the back yard.  It ran between the garage and the pool.  Several gutters were connected directly into the French Drain.  From this point, we expanded up to a larger 6 inch Drain pipe to handle the added water into the system from the gutters.  In several places the French Drain had to run through areas where Sprinkler Pipes were in the way.  We had to re-rout all the Sprinkler Pipes and Wires under the French Drain.

Once the Sprinkler System had been redesigned and the gutters had been connected, we ran the 6 inch Drain Pipe from the end of the French Drain, around the house to release through the curb.  We cut the curb and installed a 6 inch curb fitting with acrylic concrete.  A few days later a major thunderstorm poured down on the property.  The French Drain and the Drainage System Worked Perfectly.

A Channel Drain is a type of Surface Drain and many times is installed in concrete across sidewalks or driveways.  It is long and narrow with a grate on top.

Installing Channel Drain Across Sidewalk in Norman

Installing Channel Drain Across Sidewalk in Norman

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench.  A  Trench Liner is sometimes used depending on the Drainage System Design and the type of soil.   The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe.   This is to ensure that the Drain Pipe does not become clogged. A trench is dug that is slightly wider than the French Drain Pipe that is being used.  There are several sizes of French Drain Pipe.   Three Inch, Four Inch, and Six Inch are the most common sizes of French drain Pipe. The dirt that is taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed.

 

We just finished a 4 inch Drainage System in Yukon.  It was a complicated system to install.  It utilized 4 inch French Drain in the flower beds,  12 inch Surface Drains on the side of the house,  6 inch French Drain along the garage foundation with 2 Pop – Up Emitters in the back yard and 3 Curb Fittings in the front.    First we installed 4 inch French Drain in the flowerbeds on both sides of the front door.  We connected 4 inch solid Drain Pipe into the French Drain and ran them underside walk to the curb.  Next we cut the curb with a concrete saw and installed 3 curb outlets for 3 separate French Drains.

Installing a Curb Outlet for a French Drain in Oklahoma City

Installing a Curb Outlet for a French Drain in Oklahoma City

Next we installed 4 12 Inch Drain Basins with grates along both sides of the house continuing with Solid Drain Pipe to the Pop-Up Emitters on the back fence. Finally we completed the Drainage System by installing a long run of 6 inch French Drain down the side of the garage foundation.   Installing the French Drains in the flower beds was the most difficult and took the most time.  Each French Drain took over a ton of crushed limestone to fill the French Drain trench.  The Six inch French Drain took even more limestone.

French Drain in Oklahoma City


Oklahoma Drainage and Sprinkler Repair 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

    Sprinkler Repair for all aspects of Residential Sprinkler Systems

    Emergency Sprinkler Repair Service, AFTER HOURS AND WEEKENDS.

Drainage Systems, French Drains, Surface Drains, Channel Drains, Sump Pumps, Sprinkler Repair, with 26 years of experience. 

Installing Surface Drain in Driveway

 

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench.  A  Trench Liner is sometimes used depending on the Drainage System Design and the type of soil.   The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe.   This is to ensure that the Drain Pipe does not become clogged. A trench is dug that is slightly wider than the French Drain Pipe that is being used.  There are several sizes of French Drain Pipe.   Three Inch, Four Inch, and Six Inch are the most common sizes of French drain Pipe. The dirt that is taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed.

 

Oklahoma Drainage and Sprinkler Repair – 405203 9419

 

FRENCH DRAIN INSTALLATION IN EDMOND OKLAHOMA

French Drain running along foundation

French Drain running along foundation

Edmond Oklahoma has been the location for many French Drain Installations for us in the past several years.  Recently we ripped out an old Surface Drain that was under a deck.  The Surface Drain was too small for the job and did not Protect the Foundation from Standing Water.  The First step was to take out part of the deck along the wall.  Next we took out the Surface Drain and the Three Inch Pipe which was too small.  Digging a trench along the foundation came next.  We had to ensure the, “Fall” to make sure the water would run from left to right.  Next a French Drain Liner needed to be installed.  This was necessary to maintain the integrity of the trench and to keep the French Drain Pipe from filling up with sand and getting clogged over the next few years.  We then installed 4 inch ADS Perf/Soc French Drain Pipe along the course of the French Drain.  Next we connected the end of the French Drain Pipe to Solid 4 Inch ADS Drain pipe to continue along the trench to the Pop-Up Emitter at the Exit Point.

 

A good Drainage System has a point where water enters the System.  This is usually through a French Drain, Surface Drain, or a Gutter Down Spout that is connected into a Drain Pipe.   Water will run through either Perforated French Drain Pipe or Solid Drain Pipe depending on the Drainage System Design.  Water will flow down hill to an Exit Point where the water will be released out of the Drainage System.  This is a done through a Pop-Up Emitter or a Curb Fitting.

 

Cutting The Curb and Installing Curb Fitting for French Drain

Cutting The Curb and Installing Curb Fitting for French Drain

Installing Cement around Curb Fitting for French Drain

Installing Cement around Curb Fitting for French Drain

 
 

A French Drain is a long perforated pipe in the bottom of a trench.  The trench runs through the problem drainage area.  The trench is filled with gravel or crushed lime stone.  The French Drain takes in water any place that water runs into the trench.

A French Drain will move large amounts of water from the Drainage Problem Area to the Exit point.

A French Drain will Drain away water that gets to the Drainage Problem Area in 3 ways.

1.  Water gets to the problem area by falling from the sky.

2.  Water gets to the problem area by flowing down hill over the ground.

3.  Water gets to the problem area by flowing underground. (Sub-Surface water flow)

French Drain Running Through Low Areas in Yukon

French Drain Running Through Low Areas in Yukon

Number 3,  Sub-Surface water flow is the big consideration.  When doing a Drainage Diagnostic, this is the area that is many times missed or not considered by less experienced companies.    Many Times it is cheaper and more effective to install a French Drain over a Surface Drain.  A Surface Drain can’t move as much water as a French Drain, and a Surface Drain can’t Drain away Sub-Surface waterSurface Drains should be installed in areas where the Drainage Problem area is smaller and is not affected by sub-surface water.

Surface Drain

Surface Drain

The draw back to a French Drain, is that it is not a pretty as a Surface Drain.

French Drains do a great job running along foundations and driveways.  A French Drain will keep water away from cement and prevent damage to concrete if water should freeze up against it.  A French Drain can keep your foundation Dry.

 

We just finished a 4 inch Drainage System in Yukon.  It was a complicated system to install.  It utilized 4 inch French Drain in the flower beds,  12 inch Surface Drains on the side of the house,  6 inch French Drain along the garage foundation with 2 Pop – Up Emitters in the back yard and 3 Curb Fittings in the front.    First we installed 4 inch French Drain in the flowerbeds on both sides of the front door.  We connected 4 inch solid Drain Pipe into the French Drain and ran them underside walk to the curb.  Next we cut the curb with a concrete saw and installed 3 curb outlets for 3 separate French Drains.

Installing a Curb Outlet for a French Drain in Oklahoma City

Installing a Curb Outlet for a French Drain in Oklahoma City

Next we installed 4 12 Inch Drain Basins with grates along both sides of the house continuing with Solid Drain Pipe to the Pop-Up Emitters on the back fence. Finally we completed the Drainage System by installing a long run of 6 inch French Drain down the side of the garage foundation.   Installing the French Drains in the flower beds was the most difficult and took the most time.  Each French Drain took over a ton of crushed limestone to fill the French Drain trench.  The Six inch French Drain took even more limestone.

French Drain in Oklahoma City

French Drain in Oklahoma City

French Drains can utilize  several types and sizes of French Drain Pipe.  An older type that is not commonly used any more is 4 inch PVC Pipe with large half inch holes drilled in the Pipe.  This doesn’t work very well,   Because the holes are too large and the number of holes in the French Drain Pipe are too few.  Also there is no filter or “Soc” around this particular French Drain Pipe.  If it is used in sandy or loose soil the holes will clog and the pipe will fill up with sand.  PVC French Drain Pipe should be avoided.

Installing a Drain Pipe For a French Drain that Releases water through a Pop-Up Emitter at the Street

Installing a Drain Pipe For a French Drain that Releases water through a Pop-Up Emitter at the Street

ADS French Drain Pipe is much better, the holes are smaller and much more numerous.  It also comes inside a soc that acts as a filter and helps keep sand and debris out of the French Drain Pipe.  It works very well.

For Small business and Residential French Drains, Four inch ADS Perf/Soc French Drain pipe is adequate and the most common.  It is used for the majority of all French Drains installed.  French Drains can be installed using 3 inch ADS Perf/Soc but many times it is too small and can be overwhelmed by a heavy rain or from a bad design.  (Too many gutter down spouts connected directly into the French Drain, For Example)  Three Inch French Drain Pipe should be avoided if possible.

Connecting Gutter into French Drain System in Moore

Connecting Gutter into French Drain System in Moore

Six inch  ADS Perf/Soc French Drain Pipe is usually a good idea when possible.  It carries a much larger volume of water.  Six Inch French Drains are rarely overwhelmed.

The Drawbacks to 6 inch French Drain installation are:  1.  The Materials Cost is higher for six-inch French Drain Compared to Four Inch Pipe.
                                                                                                                    2.  Many times 6 Inch French Drain Pipe is too large for many applications, Such as going under a fence or sidewalk.  
                                                                                                                   3.  The trench for a 6 inch French Drain must be much larger than a 4 Inch
                                                                                                                   4.  The amount of gravel or limestone or River Rock used to Cover the 6 inch French Drain is Much larger
 
All things being considered, the performance and longevity of a 6 inch French Drain is well worth it if you are trying to protect something of value to you!  If the higher cost and the additional labor and materials are not a problem and 6 inch French Drain pipe is not too big for what you want to do then a 6 inch French Drain would be the best.  
 

FRENCH DRAIN, SURFACE DRAIN, DRAINAGE SYSTEM, OKLAHOMA CITY, NORMAN, EDMOND

 

Oklahoma Drainage and Sprinkler Repair 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

    Sprinkler Repair for all aspects of Residential Sprinkler Systems

    Emergency Sprinkler Repair Service, AFTER HOURS AND WEEKENDS

 

Hard rain in Oklahoma is common.  Many homes and businesses have drainage problems. Standing water from storm water run-off  can cause damage to grass, trees and shrubs, not to mention foundations, sidewalks and driveways. Oklahoma Drainage and Sprinkler Repair  can design and install a drainage system that may be complex using several types of drains, or basic using just a French Drain or a Surface Drain.  It depends on the customer’s needs.

 

Today we installed a Channel Drain.   It takes a lot of attention to detail.  Channel Drain installation takes several specific steps.  It is a slow process that takes confidence and experience.  I was able to train a couple of our guys on the complete process.  They learned a lot but are nowhere near ready to solo yet.

Installing Channel Drain Across Sidewalk in Norman

Installing Channel Drain Across Sidewalk in Norman

If you live in Central Oklahoma and need a French Drain to protect your home’s foundation, Give us a call.  A French Drain is a great way to keep water away from cement such as a home foundation or driveway.  When water is left standing near a driveway or sidewalk, it can cause deterioration and cracking.  A French Drain is a Good way to keep water away from problem drainage areas.  We also install Surface Drains of most types and sizes depending on our customer’s needs.

Surface Drain Installation in Edmond

Surface Drain Installation in Edmond

We can schedule a free estimate for a drainage system.  A French Drain can be an important part of a Drainage System.  A Drainage System is one or several types of drains connected to an exit point, were the unwanted water is to be released.   A French Drain may be connected to a Surface Drain which in turn may be connected to a gutter down-spout, or Channel Drain.  All the different drains are connected under ground by drain pipe to a Pop-Up Emitter or a Curb fitting to release the water.

Installing French Drain and curb fitting through curb

Installing French Drain and curb fitting through curb

What goes into a Drainage System depends on the individual Drainage Problem.  Some Drainage Problems are Simple and need only one type of Drain Connected to an exit point.  Other Drainage problems require  a more complex solution.

Channel Drain Installation in sidewalk in Oklahoma City

Channel Drain Installation in sidewalk in Oklahoma City

 


Oklahoma Drainage and Sprinkler Repair 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

    Sprinkler Repair for all aspects of Residential Sprinkler Systems

    Emergency Sprinkler Repair Service, AFTER HOURS AND WEEKENDS

 

 OKLAHOMA CITY FRENCH DRAIN

 

 

We Install French Drains by themselves and as a part of Drainage Systems to protect Driveways, Sidewalks, Foundations all over Edmond.  French Drains may be installed in Flower Beds or grassy areas too.  French Drains when installed correctly can provide many years of property protection and Piece of Mind.

Understanding why a French Drain should be installed over a Surface Drain in particular situations is just one of many variables that must be considered when Diagnosing a Drainage Problem.

Many times we are asked to look at Drainage Systems that aren’t working correctly.  Here are a few common problems that we find:

French Drain Pipe is too small for the Drainage Area.

French Drain is not connected to an Exit Point.

French Drain is installed where a Surface Drain is needed.

Surface Drain is installed where a French Drain is needed.

Too many gutters connected to French Drain.

French Drain covered with dirt.

Exit Point Covered with Dirt.

Water flow is bad for French Drain,  (trying to drain water up hill)

These are just a few of the Problems we are asked to solve when fixing a Drainage System that wasn’t designed correctly.

Drainage Systems can be made up of one drain or a combination of many drains.  Drainage  problems can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together.  Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together.

An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional Surface Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street.

A simple Drainage System might consist of a Surface Drain that is connected to a second Surface Drain which runs to a Pop-up Emitter which lets water drain over the curb and into the street.

An “Exit Point” is the term used for where all the water leaves the Drainage System.  Determining the Exit Point is very critical.  It is one of the first things we do when diagnosing a Drainage Problem.

Curb Outlet as an Exit Point for a French Drain in Edmond

Curb Outlet as an Exit Point for a French Drain in Edmond

Drainage Systems can:

1.  Keep water away from foundations — A French Drain is best because it can move Surface Water and Sub-Surface Water (water moving under ground) away from the foundation.  Many times less experienced companies install Surface Drains to keep water away from foundations.  This can be a big mistake.  A Surface Drain can’t move or drain Sub-Surface Water.   Also A Surface Drain often can’t move enough water fast enough and easily becomes overwhelmed during a heavy rain.  A Surface Drain also can’t cover or protect a broad enough area. Surface Drains should be designed in a Drainage System to be located in smaller Drainage Areas moving moderate amounts of water.  Surface Drains look better than French Drains.  If ,”appearance” is more important than Drainage Capacity, Go with the Surface Drain.  Just know what you are getting into and what your expectations should be. One side of a foundation alone,  can be over 100 feet.  A 4 inch or 6 inch French Drain is best when protecting a large area such as a foundation.

2.  Keep water away from small or in closed areas.  This might be a low area just through a gate on the side of a house, or the low area between a flowerbed and the wall of a house, or standing water on or near a sidewalk or driveway.  These types of Drainage Problems are best served with Surface Drains.  A Surface Drain can move water away from a low area that is relatively small.  This can occur in yards, flowerbeds, sidewalks and driveways.  A surface Drain is designed to move Surface Water away from a problem area to a predetermined exit point.  Surface Drains are available in many sizes.  How quickly they remove standing water is usually determined by the size of the pipe that is connected to the drain.

Simply put, a Drainage System is one or a group of underground Drain Pipes that take water away from a place that has water standing on it or flowing across it.  The water that is in the problem area, can be causing damage or may be inconvenient or both.  (Usually Both)  A simple Drainage System is a Drain for the water to enter, a Drain Pipe to move the water away from the Drain, and an Exit Point for the water to be released out of the Drain Pipe.

Drain Grates Installed in Edmond Driveway

Drain Grates Installed in Edmond Driveway

Drainage Systems quickly can become more complicated.  Considerations must include:

How does the water get to the problem area?  There may be one or many sources.

Water Sources:

1.  It falls from the sky directly

2.  It flows down hill over the surface (surface water)

3.  It flows underground under the surface (sub-surface water)

4.  It flows from the edge of a roof ( There may be many roofs near the problem area, neighbors etc.)

5.  It flows from a gutter downspout

6.  It flows over the edge of a gutter because the gutter is too small or clogged

7.  It flows up from the ground (seeps and springs are common in Oklahoma)

8.  It flows from a sprinkler system use ( yours or your neighbors)

9.  It flows from a leaking pipe ( water mains, water meters, water lines, sprinkler pipes, sprinkler valves)

There are other reasons for Drainage Problems, the above reasons are just the most common.

Once the number of water sources is determined, a rough estimate of the amount of water that needs to be drained away on average must be estimated.  This can be simplified down to “SMALL, MEDIUM, OR LARGE AMOUNTS OF WATER TO BE DRAINED AWAY.  You don’t have to be an engineer trying to calculate fluid dynamics.  Experience at diagnosing drainage problems helps however.  How much water needs to be moved will help determine the type and size of the Surface Drain or French Drain that needs to be installed.  It also helps to determine the size of Drain Pipe required for the Drainage System.  A good rule to follow is, “If in doubt, install a larger Drain and Drain Pipe.”  Unused Drainage Capacity is better than property damage caused by a Drain that is overwhelmed by too much water.

For home and small business use typical materials used are:

6 inch, 9 inch, and 12 inch Surface Drains

3 inch, 4 inch, and 6 inch Drain Pipes

3 inch, 4 inch, and 6 inch French Drains

French Drains move more water than Surface Drains —

French Drains move Surface Water and Sub-Surface Water

Surface Drains move Surface Water only

Surface Drains look nicer than French Drains in most cases

Once the type and number of drains is determined and what size Drain Pipe will connect them, an exit point must be selected.  (Where is the Drainage System going to take the water to and release it?)

curb cut

curb outlet

The Drainage Curb Fitting is installed when the desired exit point for the French Drain will release the Drainage Water into the Street.   The Drainage Curb Fitting is rectangular in shape and made to be installed through the curb.  A small section of Curb is cut out with a concrete saw.  The Section is a few inches wider than the Drainage Curb Fitting.  We then install new concrete around the curb fitting.  Once the concrete has dried, the Drain Pipe coming from a French Drain or Surface Drain is connected to the Drainage Curb fitting and then covered with dirt.

 

 

 


Oklahoma Drainage and Sprinkler Repair – 405 203 9419

Do you need Sprinkler Repair?

Winter is a time when a lot can go wrong with a Sprinkler System.   Sprinkler Pipes can freeze and break.  Sprinkler heads can crack or bust.  Above Ground Back-Flow Valves can crack or leak even during a warm winter.  Oklahoma Drainage and Sprinkler Repair can help.  Give us a call at :

EDMOND OKLAHOMA FRENCH DRAIN

 

Edmond is one of the communities in Central Oklahoma that we service.  Oklahoma Drainage and Sprinkler Repair has installed almost a thousand French Drains in the Edmond community in the past 21 years.  Edmond has many hills and valleys.  Many Neighborhoods are built on hillsides.  This causes many Drainage Problems. We have installed French Drains by themselves and as a part of Drainage Systems to protect Driveways, Sidewalks, Foundations all over Edmond.  French Drains may be installed in Flower Beds or grassy areas too.  French Drains when installed correctly can provide many years of property protection and Piece of Mind.

 

 

 


FRENCH DRAIN  CONNECTED TO GUTTERS

Many different types of Drains can be hooked together by one Drain Pipe.  The Drain Pipe then running to an Exit Point makes up a Drainage System.  One common type of Drain used in a Drainage System is A “French Drain.”  Many times a French Drain is installed close to a building foundation or in a low area next to a home or business.  This puts the French Drain in close proximity to Gutter Down Spouts.  Rather than have water come off the roof and out the Down Spout and on to the ground below, many times it is much better to tie a Gutter Down Spout Directly into a French Drain or near by Drain Pipe depending on the Drainage System Design.   Connecting The Down Spouts Directly into a French Drain is much  more efficient and causes suction to occur in the French Drain.  Connection of Gutter Down Spouts to a French Drain makes the Drainage System work better.

Connecting Gutter into French Drain System

Connecting Gutter into French Drain System

 

One Problem with connecting Gutter Down Spouts into a French Drain is overwhelming the Drainage System with too much water.  Three Gutter Down Spouts is usually OK to connect into a French Drain.  More than 3 Down Spouts can be too many.  The Drainage System Design should also take into account the size of the French Drain and the Gutters.  If you have a large long French Drain or over-sized gutters,  the number of Gutter Down Spouts connected into the French Drain Should be reduced.  This problem can usually be solved by increasing the size of the French DrainPipe.  This usually means moving up from a 4 inch French Drain Pipe to a 6 inch French Drain Pipe.  Four inch is the most common size of French Drain Pipe.  If you have more than 3 gutter Down Spouts to connect, you should move up to a 6 inch French Drain Pipe.

Gutter connected straight into 6 inch French Drain System

Gutter connected straight into 6 inch French Drain System