Archive for the ‘Drain Repair’ Category


Don’t despair! We provide Sprinkler Repair.

OK the rhyme is a little lame but it is no reflection on the quality of service or the level of expertise that we provide.

Oklahoma Drainage and Sprinkler Repair has been providing Expert Sprinkler Repair since 1993.  During that time we have seen it all and done it all where residential Sprinkler Repair is concerned.

We service all of Central and Western Oklahoma.

1 SPRINKLER VALVE

Replacing Broken Sprinkler Valve in Norman.

If you need a Sprinkler Head moved, adjusted, repaired or replaced we can handle the job.

If you have any type of problem with your sprinkler valves we can provide the solution.

Sprinkler Controller trouble?  No Problem.  We service all brands and models.

 

Many times Sprinkler Wires get damaged or cut.  Sprinkler Wiring runs underground from the Sprinkler Valves to the Sprinkler Controller.  Many times the wires become damaged when digging is done in your yard.  Installing new phone lines for example causes cuts in Sprinkler Wire.

If the phone lines are installed during the winter when the Sprinkler System is not being used, you may not realize that you have a problem until the following spring.

Finding cut sprinkler wiring can be very difficult.  This is one area where there is no substitute for experience.

Oklahoma Drainage and Sprinkler Repair has been finding Cut Sprinkler Wires and fixing them since 1993.

Installing in-line drains in a sprinkler system is a service that we also provide.  Many times a sprinkler system has no drains put in when the Sprinkler System is first installed.

We are happy to install them for you.

An in-line sprinkler drain automatically drains all the water out of the Sprinkler Pipes immediately after your sprinkler system runs.  This relieves stress on the pipes and joints and also prevents pipes from freezing and breaking because there is still water in your system from last summer.  SPRINKLER PIPES CAN’T FREEZE IF THERE IS NO WATER IN THEM.

 


French Drains and all types of Drainage Systems involves digging Drainage Trenches and Installing Drain Pipes.  One issue that must be addressed is Slope or Fall” of the of the Drain Pipe in the Drainage Trench.   The Drain Pipe must run downhill to the exit point to move the water away from the problem area.

If you need to move Forward or Back in this Blog Series, Click Below:

Previous Blog                  Next Blog

drain trench

Drainage Trench Running Downhill

In many cases slope is easy to determine if the distance from the drain to the exit is obliviously down hill.   The trouble is installing a French Drain or a Drainage System where the drain pipe is not always on a pronounced slope.  A slight slope can be hard to see. If the ground looks level then the water won’t flow very quickly, If at all.  If the entrance drain is slightly higher than the exit, say only a few inches, then the water will flow across level ground to the exit point.  Problem is, the water will move very slowly as long as water is still coming into the French Drain.  It pushes the water in front of it out of the exit very slowly.  Movement will stop when water stops coming into the Drain.  It will stay in the pipe and just sit there till the next time it rains.

If you are Installing a Drainage System across level ground, it will never drain very well.

If you are not sure if a Drainage System is possible because there might not be enough Slope,  there is a simple test you can run.  This test takes a good bit of digging.

Start digging the trench where the drain pipe will run.   Lets say for example that its about 60 feet.  Start digging where the drain will be.  Typically a 4 inch drain pipe will need to be installed in a trench 8 to 16 inches deep, depending on your needs.  Dig about 10 feet from where the drain will be toward the exit point.  Once you have dug a trench at least 8 inches deep, and about 10 feet long toward the exit,  Take a hose and place it in the trench where the drain will be installed. There should not be pipe in the trench at this time, just the empty trench.

Turn on the hose so a small amount of water is coming out.  The water will start to flow down the trench from where the drain will be, toward the exit.  Again there is no drain pipe in the trench.

trench water test

Water test for a Drain Pipe

Watch the water as it flows down the Drainage Trench.   In some areas it will flow quickly which is good.  Look for areas where water flows more slowly and begins to pool.  Once this occurs, turn off the hose and get your shovel.  With water still in the trench, dig downhill from the pooling spot.  Remove the dirt that is slowing the waters flow toward the exit.  Repeat this process until you have reached the exit point of the Drainage System.

This may seem like a lot of unnecessary work.  Believe me it is worth it.  Once the water flows at a fairly steady rate all the way to the exit, you have ” Set the Flow of the Drain.”

This process is called “Setting The flow.”

There are benefits to taking this process seriously.

First it will tell you if the flow is even possible for the Drainage System that you want to install.  If you can’t get the water to flow to the Exit Point Cover up your Drainage Trench and Consider Other Options because this particular Drainage Design will not work.  If you can redesign your system by moving your drain pipe or your exit point, then do so.  A Sump Pump may be your only option if moving the drain pipe or the exit does not improve things.   Sump Pumps will be covered in a future blog.

Second, If you were successful in setting the flow, then you will roughly know how fast the water will flow in your Drainage System.  It will give you a “Worse Case Scenario” for your Drain’s Performance.

Water will always flow better and faster and more efficiently in a Drain Pipe, than in a trench.

If the water is flowing pretty good in the Drainage Trench without a Drain Pipe in it yet, then it will flow even better once the Drain Pipe is installed.

This process is much better than blindly digging a drainage trench and installing a Drainage System.  It will keep you from installing something that doesn’t work!

Previous Blog                  Next Blog

 


French Drain Installation Or Do You Need A Surface Drain?

Many Folks don’t know the difference.   Actually there are many differences and a few similarities.  One difference is, a French Drain takes in a larger amount of water into the drain Pipe than a Surface Drain.  There are advantages to Surface Drains as well.

 

A French Drain Is a Perforated Drain Pipe in a Trench with Gravel or Limestone covering the trench with the pipe.  Many times there is a “Sock” around the pipe to act as a filter.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.

French Drains as part of a Drainage System – 

Many times people use the term ” French Drain” as general name for a Drain used in or around your home.  French Drains are designed to move a lot of water over a large flooded area.  They are also designed to take water in on the surface of the ground or below the surface of the ground.  This is very important if the water coming into the flooded area is moving through the ground or coming up from underneath.  ” Sub Surface Water Movement.”  The picture below is not a French Drain!

A French Drain looks like this

A French Drain Can Handle Standing Water

A French Drain can take in water in a broad area.  It can move a much larger volume of water compared to a Surface Drain.  Also, it can move sub surface water moving into the area where a Surface Drain won’t move any water at all.

Surface Drains are designed to move surface water only on a smaller scale in confined areas.

Each solves specific drainage problems.  A Drainage System may use one or both together or even several using many types of drains.

Do you have standing water in a large area in your yard?  Typically this calls for a French Drain.  A French Drain is a great way to control standing water in a large grassy area.  It can also protect areas from flooding to a certain degree.  As long as the French Drains capacity to move water is not exceeded.  If the French Drains capacity is exceeded then water will stand in the drainage area until the rain stops and the drain has time to catch up.  A good way to prevent this is to install a bigger French Drain with a larger pipe.  The difference between a 3 inch French Drain and a 6 inch French Drain is huge.

Another way to beef up a French Drain is to connect gutter down spouts in front of the French Drain.  The water coming off the roof causes suction in the French Drain Behind it.  This greatly increases the French Drains ability to move water without increasing the size of the French Drain Pipe.

Gutter Downspout Connected to 6 Inch French Drain

 

Oklahoma Drainage and Sprinkler Repair recently diagnosed a Drainage Problem in  South Oklahoma City.  The Home owner had a sump Pump in their basement that was fed from a French Drain outside the Basement Wall.  The French Drain was 14 feet down along the Stem wall of the house.  The French Drain Pipe was cheap and had collapsed.  We brought in a Mini Excavator and dug up the pipe and replaced it with Durable ADS 4 inch perf/soc French Drain pipe.  In the end, we were able to dig up the pipe and Replace it.

New Trench for French Drain

Next we installed a new exit for the water by installing a curb fitting.

No more flooding in the customers basement.  A few weeks later our customer was able to lay carpet in the basement with no problems.

French Drain Installed Along Stem Wall

 

Installing Drainage Curb Fitting for a French Drain in South Oklahoma City

 

Curb Fitting with Acrylic Cement For French Drain

 

FRENCH DRAIN  CONNECTED TO GUTTERS

Many different types of Drains can be hooked together by one Drain Pipe.  The Drain Pipe then running to an Exit Point makes up a Drainage System.  One common type of Drain used in a Drainage System is A “French Drain.”  Many times a French Drain is installed close to a building foundation or in a low area next to a home or business.  This puts the French Drain in close proximity to Gutter Down Spouts.  Rather than have water come off the roof and out the Down Spout and on to the ground below, many times it is much better to tie a Gutter Down Spout Directly into a French Drain or near by Drain Pipe depending on the Drainage System Design.   Connecting The Down Spouts Directly into a French Drain is much  more efficient and causes suction to occur in the French Drain.  Connection of Gutter Down Spouts to a French Drain makes the Drainage System work better.

Do you have water standing in your yard after a hard rain? Does your sidewalk become a moat during a thunder-storm? Is standing water causing your foundation to deteriorate and break down? Is water seeping into your home and causing mold?

Storm-water run off can cause many types of problems. Oklahoma Drainage and Sprinkler Repair can diagnose your drainage issues and design a Drainage System to fit your specific needs. We install many types of drains including: French Drains, Channel Drains, Surface Drains, Basin Drains, Trench Drains, Basement Drains, and Sump Pumps.

colored drain gravel

Colored Gravel covering a French Drain


French Drain Installation Or Do You Need A Surface Drain?

Many Folks don’t know the difference.   Actually there are many differences and a few similarities.  One difference is, a French Drain takes in a larger amount of water into the drain Pipe than a Surface Drain.  There are advantages to Surface Drains as well.

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.

Oklahoma Drainage and Sprinkler Repair recently diagnosed a Drainage Problem in  South Oklahoma City.  The Home owner had a sump Pump in their basement that was fed from a French Drain outside the Basement Wall.  The French Drain was 14 feet down along the Stem wall of the house.  The French Drain Pipe was cheap and had collapsed.  We brought in a Mini Excavator and dug up the pipe and replaced it with Durable ADS 4 inch perf/soc French Drain pipe.  In the end, we were able to dig up the pipe and Replace it.

French Drain Detail

New Trench for French Drain

Next we installed a new exit for the water by installing a curb fitting.

No more flooding in the customers basement.  A few weeks later our customer was able to lay carpet in the basement with no problems.

French Drain side of House

French Drain Installed Along Stem Wall

 

Installing Drainage Curb Fitting for a French Drain in South Oklahoma City

 

curb cement outlet

Curb Fitting with Acrylic Cement For French Drain

 

FRENCH DRAIN  CONNECTED TO GUTTERS

Many different types of Drains can be hooked together by one Drain Pipe.  The Drain Pipe then running to an Exit Point makes up a Drainage System.  One common type of Drain used in a Drainage System is A “French Drain.”  Many times a French Drain is installed close to a building foundation or in a low area next to a home or business.  This puts the French Drain in close proximity to Gutter Down Spouts.  Rather than have water come off the roof and out the Down Spout and on to the ground below, many times it is much better to tie a Gutter Down Spout Directly into a French Drain or near by Drain Pipe depending on the Drainage System Design.   Connecting The Down Spouts Directly into a French Drain is much  more efficient and causes suction to occur in the French Drain.  Connection of Gutter Down Spouts to a French Drain makes the Drainage System work better.

Do you have water standing in your yard after a hard rain? Does your sidewalk become a moat during a thunder-storm? Is standing water causing your foundation to deteriorate and break down? Is water seeping into your home and causing mold?

Storm-water run off can cause many types of problems. Oklahoma Drainage and Sprinkler Repair can diagnose your drainage issues and design a Drainage System to fit your specific needs. We install many types of drains including: French Drains, Channel Drains, Surface Drains, Basin Drains, Trench Drains, Basement Drains, and Sump Pumps.

gravel colored

Colored Gravel for a French Drain

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.

Just what is a “French Drain?” Many times people incorrectly

French drain in grass
A French Drain can protect your foundation!

use the phrase, “French Drain,” when they mean “Surface Drain” or “Channel Drain.”

A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench. The French Drain Trench runs through a Problem Drainage Area that needs to be drained.   The French Drain Pipe is perforated (Full of Small Holes) and has Neo-Prene Soc around the pipe.  This soc helps prevent debris from clogging the French Drain Pipe.

Perforated French Drain Pipe

The dirt that was taken out to make the trench is hauled away. It is replaced by some type of small stone or gravel depending on what is desired or available. I prefer crushed 1 inch lime stone. It is the most economical option in my area. Pea Gravel or some other type of small stone can work just as well. The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level). In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed. This helps maintain the integrity of the trench over time. It also increases the cost of the French Drain and the amount of time to install it. I install a trench liner in a French Drain about 20% of the time. Most of the time a liner in not needed.

French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations. It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.

French Drain with Colored Gravel

The main downfall of a French Drain is that they, for the most part aren’t very pretty. They don’t look very nice in a yard once they are completed.

Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the lime stone. Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel. This is Ok. It won’t have a measurable effect on the performance of the drain.

DON’T COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT. THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT. DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.

DECORATIVE STONE CAN BE USED TO COVER A FRENCH DRAIN AND THEY LOOK GREAT AND LAST A LIFETIME.

Drainage Systems can be made up of one drain or a combination of many drains.  Drainage  problems can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together. Many times a French Drain, might be connected to a Surface Drain,  which then could be connected to another French Drain.   Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together.

Cutting The Curb and Installing Curb Fitting With Acrylic Cement
Cutting The Curb for French Drain Outlet

An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional French Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street.

A simple Drainage System might consist of a French Drain  which runs to a Pop-up Emitter which lets water drain over the curb and into the street.

An “Exit Point” is the term used for where all the water leaves the Drainage System.  Determining the Exit Point is very critical.  It is one of the first things we do when diagnosing a Drainage Problem.

Drainage Systems can:

1.  Keep water away from foundations — A French Drain is best because it can move Surface Water and Sub-Surface Water (water moving under ground) away from the foundation.  Many times less experienced companies install Surface Drains to keep water away from foundations.  This can be a big mistake.  A Surface Drain can’t move or drain Sub-Surface Water.   Also A Surface Drain often can’t move enough water fast enough and easily becomes overwhelmed during a heavy rain.  A Surface Drain also can’t cover or protect a broad enough area. Surface Drains should be designed in a Drainage System to be located in smaller Drainage Areas moving moderate amounts of water.  Surface Drains look better than French Drains.  If ,”appearance” is more important than Drainage Capacity, Go with the Surface Drain.  Just know what you are getting into and what your expectations should be. One side of a foundation alone,  can be over 100 feet.  A 4 inch or 6 inch French Drain is best when protecting a large area such as a foundation.

2.  Keep water away from small or enclosed areas.  This might be a low area just through a gate on the side of a house, or the low area between a flowerbed and the wall of a house, or standing water on or near a sidewalk or driveway.  These types of Drainage Problems are best served with Surface Drains.  A Surface Drain can move water away from a low area that is relatively small.  This can occur in yards, flowerbeds, sidewalks and driveways.  A surface Drain is designed to move Surface Water away from a problem area to a predetermined exit point.  Surface Drains are available in many sizes.  How quickly they remove standing water is usually determined by the size of the pipe that is connected to the drain.

Simply put, a Drainage System is one or a group of underground Drain Pipes that take water away from a place that has water standing on it or flowing across it.  The water that is in the problem area, can be causing damage or may be inconvenient or both.  (Usually Both)  A simple Drainage System is a Drain for the water to enter, a Drain Pipe to move the water away from the Drain, and an Exit Point for the water to be released out of the Drain Pipe.

Drainage Systems quickly can become more complicated.  Considerations must include:

How does the water get to the problem area?  There may be one or many sources.

Water Sources:

1.  It falls from the sky directly

2.  It flows down hill over the surface (surface water)

3.  It flows underground under the surface (sub-surface water)

4.  It flows from the edge of a roof ( There may be many roofs near the problem area, neighbors etc.)

5.  It flows from a gutter downspout

6.  It flows over the edge of a gutter because the gutter is too small is is clogged

7.  It flows up from the ground (seeps and springs are common in Oklahoma)

8.  It flows from a sprinkler system use ( yours or your neighbors)

9.  It flows from a leaking pipe ( water mains, water meters, water lines, sprinkler pipes, sprinkler valves)

There are other reasons for Drainage Problems, the above reasons are just the most common.

Once the number of water sources is determined, a rough estimate of the amount of water that needs to be drained away on average must be estimated.  This can be simplified down to “SMALL, MEDIUM, OR LARGE AMOUNTS OF WATER TO BE DRAINED AWAY.  You don’t have to be an engineer trying to calculate fluid dynamics.  Experience at diagnosing drainage problems helps however.  How much water needs to be moved will help determine the type and size of the Surface Drain or French Drain that needs to be installed.  It also helps to determine the size of Drain Pipe required for the Drainage System.  A good rule to follow is, “If in doubt, install a larger Drain and Drain Pipe.”  Unused Drainage Capacity is better than property damage caused by a Drain that is overwhelmed by too much water.

For home and small business use typical materials used are:

6 inch, 9 inch, and 12 inch Surface Drains

3 inch, 4 inch, and 6 inch Drain Pipes

3 inch, 4 inch, and 6 inch French Drains

French Drains move more water than Surface Drains —

French Drains move Surface Water and Sub-Surface Water

Surface Drains move Surface Water only

Surface Drains look nicer than French Drains in most cases

Once the type and number of drains is determined and what size Drain Pipe will connect them, an exit point must be selected.  (Where is the Drainage System going to take the water to and release it?)

The Drainage Curb Fitting is installed when the desired exit point for the French Drain will release the Drainage Water into the Street.   The Drainage Curb Fitting is rectangular in shape and made to be installed through the curb.  A small section of Curb is cut out with a concrete saw.  The Section is a few inches wider than the Drainage Curb Fitting.  We then install new concrete around the curb fitting.  Once the concrete has dried, the Drain Pipe coming from a French Drain or Surface Drain is connected to the Drainage Curb fitting and then covered with dirt.

 

 

 


Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.

FRENCH DRAIN IN EDMOND OKLAHOMA

Oklahoma Drainage and Sprinkler RepairFrench Drain Installation, Drainage System Design, Expert Lawn Sprinkler RepairDrain Repair 

Recently Oklahoma Drainage and Sprinkler Repair installed a large 6 inch French Drain in Edmond.  The customer had water running under his back porch step and into his basement.  We did a Free Drainage Diagnostic and Estimate.  The French Drain design that we proposed would intercept the surface water and subsurface water that was flowing under the steps.  The French Drain design called for a 6 inch French Drain to be installed above and several feet away from the steps.  It would run around the house parallel to the foundation and about 5 feet to the East.  The French Drain would run past the steps to a point where water must cross the French Drain or run up hill to the steps which in this case was not possible.  Once past the steps, the French Drain would transition to Solid 6 inch Drain Pipe and continue on around the house to the Pop-Up Emitter down hill in the side yard.  Along the way we attached several Gutter Down Spouts into the French Drain.

 

Curb Outlet for French Drain in Edmond

Curb Outlet for French Drain in Edmond

French Drain Installation

Oklahoma Drainage and Sprinkler Repair has been diagnosing and solving Drainage Problems since 1993.  Water has the ability to get into places around your home where you really don’t want it to be.  Some drainage problems are easy to solve.  Typically water enters the problem drainage area one way from one source.  The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources.  Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.

An example of this occurs when water is running into a problem area in an obvious way over the ground where you can see it.

Simple enough.

A drainage system is installed with a surface drain as the “intake” with drainage pipe running to an exit point.  Initially the water drains away and everything looks great.  The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area.  The primary water source was solved, ( The surface water run off ) but the secondary water source was not.  Which was sub-surface water, (ground water) running into the area.  A surface drain can’t drain “ground water.”  A French Drain should have initially been installed instead of a Surface Drain.  A French Drain can drain both Surface Water and Ground Water.

 

A French Drain Can Handle Standing Water

 FRENCH DRAIN IN EDMOND OKLAHOMA, DRAINAGE CONTRACTOR

Oklahoma Drainage and Sprinkler Repair Recently  installed a large 6 inch French Drain in Edmond.  The customer had water running under his back porch step and into his basement.  We did a Free Drainage Diagnostic and Estimate.  The French Drain design that we proposed would intercept the surface water and subsurface water that was flowing under the steps.  The French Drain design called for a 6 inch French Drain to be installed above and several feet away from the steps.  It would run around the house parallel to the foundation and about 5 feet to the East.  The French Drain would run past the steps to a point where water must cross the French Drain or run up hill to the steps which in this case was not possible.  Once past the steps, the French Drain would transition to Solid 6 inch Drain Pipe and continue on around the house to the Pop-Up Emitter down hill in the side yard.  Along the way we attached several Gutter Down Spouts into the French Drain.

 

French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench.  A  Trench Liner is sometimes used depending on the Drainage System Design and the type of soil.   The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe.   This is to ensure that the Drain Pipe does not become clogged. A trench is dug that is slightly wider than the French Drain Pipe that is being used.  There are several sizes of French Drain Pipe.   Three Inch, Four Inch, and Six Inch are the most common sizes of French drain Pipe. The dirt that is taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed.

A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.

Oklahoma Drainage and Sprinkler Repair Services all of Central Oklahoma including: Norman, Moore, Edmond, Yukon, Mustang, Oklahoma City, Midwest City, Del City, Blanchard, Newcastle, Purcell and Chickasha.

 

Keep water off your driveway with a channel drain

 Standing water comes from many sources.  It causes damage to  sidewalks, driveways, and foundations not to mention plants, trees, and  grass.  Does the side of your house flood because your neighbor doesn’t  have gutters, or does your sidewalk turn into a moat after a heavy rain,  or worst of all, is water seeping into your foundation and duct work  after a thunderstorm?  Theses are just a few of the Drainage  Problems that Oklahoma Drainage and Sprinkler Repair can help with.  We can design a Drainage  System to fit your specific needs.  We install many types  of Drains  to solve many types of problems.    French  Drains, Surface  Drains, Channel  Drains, Basement  Drains, Trench Drains, Basin Drains, and Sump  Pumps are utilized.

 

 

Just what is a “French Drain?”  Many times people incorrectly

use the phrase, “French Drain,”  to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drain Pipe is connected underground to an outlet on the Drain BasinStorm-Water Drains through the grate into the Drain Basin.  Once in the Drain Basin,basin through a Drain Pipe.  The Storm-Water continues downhill in an underground Drain Pipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

Cutting the Curb for a French Drain Outlet

Surface Drain and Drain Pipe

A Channel Drain is a type of Surface Drain and many times is installed in


Oklahoma Drainage and Sprinkler Repair 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

    Sprinkler Repair for all aspects of Residential Sprinkler Systems

    Emergency Sprinkler Repair Service, AFTER HOURS AND WEEKENDS.

Drainage Systems, French Drains, Surface Drains, Channel Drains, Sump Pumps, Sprinkler Repair, with 26 years of experience. 

 

Just what is a “French Drain?” Many times people incorrectly

French Drain can protect your foundation!

use the phrase, “French Drain,” when they mean “Surface Drain” or “Channel Drain.”

A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench. The French Drain Trench runs through a Problem Drainage Area that needs to be drained.   The French Drain Pipe is perforated (Full of Small Holes) and has Neo-Prene Soc around the pipe.  This soc helps prevent debris from clogging the French Drain Pipe.

The dirt that was taken out to make the trench is hauled away. It is replaced by some type of small stone or gravel depending on what is desired or available. I prefer crushed 1 inch lime stone. It is the most economical option in my area. Pea Gravel or some other type of small stone can work just as well. The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level). In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed. This helps maintain the integrity of the trench over time. It also increases the cost of the French Drain and the amount of time to install it. I install a trench liner in a French Drain about 20% of the time. Most of the time a liner in not needed.

A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations. It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.

French Drain with Colored Gravel

The main downfall of a French Drain is that they, for the most part aren’t very pretty. They don’t look very nice in a yard once they are completed.

Drain Pipe for French Drain running under sidewalk

French Drain Pipe under sidewalk

SPRINKLER REPAIRDRAINAGE SYSTEMS FRENCH DRAINSPRINKLER ADJUSTMENTSURFACE DRAIN EMERGENCY SPRINKLER REPAIR

 

.

French Drain with stepping stones

French Drain with stepping stones

 

French Drains can be installed by themselves, or as part of a Drainage System that uses other French Drains, Surface Drains, or other Drain combinations.  Typically a French Drain is used to protect a broad area that has a lot of standing water.  A French Drain might run along side a homes foundation, or beside a driveway, or on any Drainage Project where Sub-Surface water is the primary problem.  If water is running toward your home under ground ( through sandy soil), A French Drain is the only Solution  for draining away water flowing under ground.

 

If you live in Oklahoma City and need a French Drain installed in your yard, or along your driveway, or near your foundation, give CMG a call.  If you live in Edmond or Norman and need a Surface Drain installed in the concrete in your sidewalk or driveway, we can help.  If you live in Mustang or Yukon and would like to protect your trees or flower beds from standing water with a French Drain, CMG specializes in just that!

 

If you have Drainage Issues with your property, give Oklahoma Drainage and Sprinkler Repair a call.  We install a variety of Drains to solve a variety of Drainage Problems.  We utilize and install:  French Drains, Surface Drains, Channel Drains, Basement Drains, Trench Drains, Basin Drains and Sump Pumps.  If you live in Central Oklahoma and need a Drainage System installed , give us a call.


Norman Oklahoma French Drain System, Sprinkler Repair

French Drain Installation in Norman

Recently  Norman Oklahoma had 4 inches of rain in two hours.  That’s the most rain in a short time that I can remember.  Storm-Water runoff can cause damage to all types of property and buildings.  Water getting inside your house is never a good thing.  A Drainage System that utilizes a French Drain can help.  Drains can protect your home and property from water damage.  Oklahoma Drainage and Sprinkler Repair installs a wide variety of Drains in many different places.  A Drain or Group of Drains with Drain Pipe going to an exit point is a “Drainage System.”

Large 6 Inch French Drain Installed in Norman
Large 6 Inch French Drain Installed in Norman

Drainage Systems can be made up of one drain or a combination of many drains.  Drainage  problems can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together.  Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together.

An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional Surface Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street.

A simple Drainage System might consist of a Surface Drain that is connected to a second Surface Drain which runs to a Pop-up Emitter which lets water drain over the curb and into the street.

An “Exit Point” is the term used for where all the water leaves the Drainage System.  Determining the Exit Point is very critical.  It is one of the first things we do when diagnosing a Drainage Problem.

Drainage Systems can:

1.  Keep water away from foundations — A French Drain is best because it can move Surface Water and Sub-Surface Water (water moving under ground) away from the foundation.  Many times less experienced companies install Surface Drains to keep water away from foundations.  This can be a big mistake.  A Surface Drain can’t move or drain Sub-Surface Water.   Also A Surface Drain often can’t move enough water fast enough and easily becomes overwhelmed during a heavy rain.  A Surface Drain also can’t cover or protect a broad enough area. Surface Drains should be designed in a Drainage System to be located in smaller Drainage Areas moving moderate amounts of water.  Surface Drains look better than French Drains.  If ,”appearance” is more important than Drainage Capacity, Go with the Surface Drain.  Just know what you are getting into and what your expectations should be. One side of a foundation alone,  can be over 100 feet.  A 4 inch or 6 inch French Drain is best when protecting a large area such as a foundation.

Surface Drain Installed next to sidewalk in Oklahoma City.
Surface Drain Installed next to sidewalk in Oklahoma City.

2.  Keep water away from small or enclosed areas.  This might be a low area just through a gate on the side of a house, or the low area between a flowerbed and the wall of a house, or standing water on or near a sidewalk or driveway.  These types of Drainage Problems are best served with Surface Drains.  A Surface Drain can move water away from a low area that is relatively small.  This can occur in yards, flowerbeds, sidewalks and driveways.  A Surface Drain is designed to move Surface Water away from a problem area to a predetermined exit point.  Surface Drains are available in many sizes.  How quickly they remove standing water is usually determined by the size of the Drain Pipe that is connected to the Drain.

Simply put, a Drainage System is one or a group of underground Drain Pipes that take water away from a place that has water standing on it or flowing across it.  The water that is in the problem area, can be causing damage or may be inconvenient or both.  (Usually Both)  A simple Drainage System is a Drain for the water to enter, a Drain Pipe to move the water away from the Drain, and an Exit Point for the water to be released out of the Drain Pipe.

Drainage Systems quickly can become more complicated.  Considerations must include:

How does the water get to the problem area?  There may be one or many sources.

Water Sources:

1.  It falls from the sky directly

2.  It flows down hill over the surface (surface water)

3.  It flows underground under the surface (sub-surface water)

4.  It flows from the edge of a roof ( There may be many roofs near the problem area, neighbors etc.)

5.  It flows from a gutter downspout

6.  It flows over the edge of a gutter because the gutter is too small is is clogged

7.  It flows up from the ground (seeps and springs are common in Oklahoma)

8.  It flows from a sprinkler system use ( yours or your neighbors)

9.  It flows from a leaking pipe ( water mains, water meters, water lines, sprinkler pipes, sprinkler valves)

There are other reasons for Drainage Problems, the above reasons are just the most common.

Once the number of water sources is determined, a rough estimate of the amount of water that needs to be drained away on average must be estimated.  This can be simplified down to “SMALL, MEDIUM, OR LARGE AMOUNTS OF WATER TO BE DRAINED AWAY.  You don’t have to be an engineer trying to calculate fluid dynamics.  Experience at diagnosing drainage problems helps however.  How much water needs to be moved will help determine the type and size of the Surface Drain or French Drain that needs to be installed.  It also helps to determine the size of Drain Pipe required for the Drainage System.  A good rule to follow is, “If in doubt, install a larger Drain and Drain Pipe.”  Unused Drainage Capacity is better than property damage caused by a Drain that is overwhelmed by too much water.

For home and small business use typical materials used are:

6 inch, 9 inch, and 12 inch Surface Drains

3 inch, 4 inch, and 6 inch Drain Pipes

3 inch, 4 inch, and 6 inch French Drains

French Drains move more water than Surface Drains —

French Drains move Surface Water and Sub-Surface Water

Surface Drains move Surface Water only

Surface Drains look nicer than French Drains in most cases

Once the type and number of drains is determined and what size Drain Pipe will connect them, an exit point must be selected.  (Where is the Drainage System going to take the water to and release it?)

The Drainage Curb Fitting is installed when the desired exit point for the French Drain will release the Drainage Water into the Street.   The Drainage Curb Fitting is rectangular in shape and made to be installed through the curb.  A small section of Curb is cut out with a concrete saw.  The Section is a few inches wider than the Drainage Curb Fitting.  We then install new concrete around the curb fitting.  Once the concrete has dried, the Drain Pipe coming from a French Drain or Surface Drain is connected to the Drainage Curb fitting and then covered with dirt.

The Drainage Pop-Up Emitter is connected to the end of a Drain Pipe.  It is downhill from a French Drain or a Surface Drain.  It is a small release basin with a green pop-up lid.  When releasing water, it pops up about an inch to release the water from the French Drain or Surface Drain.  When the Storm Water has moved through the Drainage System and out of the Pop-Up Emitter, the green lid closes back to its original closed position.  The emitter is designed to release water out into a yard or down a hill or other desirable Drainage Exit Point where there is no curb.

Popup Emitter to release water from a Drainage System in Yukon.
Popup Emitter to release water from a Drainage System in Yukon.

Drainage System installationand design is a big part of our business.  Does your sidewalk turn into a moat after a hard rain?  Does part of your yard look like a pond after a thunderstorm?  Worst of all, are you experiencing concrete deterioration to your foundation, sidewalk, or driveway.  We can design a Drainage System to solve your Drainage Problems Our Drainage Systems can be simple or complex.  We utilize, French Drains, Surface Drains, Channel Drains, Basin Drains, Basement Drains, Trench Drains, andSump Pumps.  Estimates are free!

French Drain Installation In Yukon

Oklahoma Drainage and Sprinkler Repair : Servicing all of Central and Western Oklahoma since 1993.

Standing Water on Your Driveway?  A Surface Drain set in concrete may be what you need. Or maybe you need a French Drain Running alongside your driveway instead.  Handling water problems is what we are good at.  If you need help, Oklahoma Drainage can provide the best solution for your unwanted water problems.

A good place for a French Drain

We just finished a 4 inch Drainage System in Yukon.  It was a complicated system to install.  It utilized 4 inch French Drain in the flower beds,  12 inch Surface Drains on the side of the house,  6 inch French Drain along the garage foundation with 2 Pop – Up Emitters in the back yard and 3 Curb Fittings in the front.    First we installed 4 inch French Drain in the flowerbeds on both sides of the front door.  We connected 4 inch solid Drain Pipe into the French Drain and ran them underside walk to the curb.  Next we cut the curb with a concrete saw and installed 3 curb outlets for 3 separate French Drains.

Next we installed 4 12 Inch Drain Basins with grates along both sides of the house continuing with Solid Drain Pipe to the Pop-Up Emitters on the back fence. Finally we completed the Drainage System by installing a long run of 6 inch French Drain down the side of the garage foundation.   Installing the French Drains in the flower beds was the most difficult and took the most time.  Each French Drain took over a ton of crushed limestone to fill the French Drain trench.  The Six inch French Drain took even more limestone.

 Oklahoma Drainage and Sprinkler Repair

Hey Oklahoma, We are expanding to service all of Western Oklahoma as well as Central Oklahoma.  If you live in Elk City, and need a French Drain, we can help.  If water is standing on your driveway in Clinton, Give us a call.  Duncan, Lawton, and Altus are all new areas of service for us.

Since 1993 Oklahoma Drainage and Sprinkler Repair has solved all types of standing water and drainage issues.  We install Drainage Systems that utilize French Drains, Surface, Drains, Channel Drains, and Sump Pumps depending on the customers needs.

If you have water in the wrong place , we can help!

We also have Decades of experience repairing all types of Lawn Sprinkler Problems.  Fixing broken sprinkler heads, sprinkler valve problems and controller trouble just to name a few things.

French Drains as part of a Drainage System – 

Many times people use the term ” French Drain” as general name for a Drain used in or around your home.  French Drains are designed to move a lot of water over a large flooded area.  They are also designed to take water in on the surface of the ground or below the surface of the ground.  This is very important if the water coming into the flooded area is moving through the ground or coming up from underneath.  ” Sub Surface Water Movement.”  The picture below is not a French Drain!

A French Drain looks like this

A French Drain Can Handle Standing Water

A French Drain can take in water in a broad area.  It can move a much larger volume of water compared to a Surface Drain.  Also, it can move sub surface water moving into the area where a Surface Drain won’t move any water at all.

Surface Drains are designed to move surface water only on a smaller scale in confined areas.

Each solves specific drainage problems.  A Drainage System may use one or both together or even several using many types of drains.

Do you have standing water in a large area in your yard?  Typically this calls for a French Drain.  A French Drain is a great way to control standing water in a large grassy area.  It can also protect areas from flooding to a certain degree.  As long as the French Drains capacity to move water is not exceeded.  If the French Drains capacity is exceeded then water will stand in the drainage area until the rain stops and the drain has time to catch up.  A good way to prevent this is to install a bigger French Drain with a larger pipe.  The difference between a 3 inch French Drain and a 6 inch French Drain is huge.

Another way to beef up a French Drain is to connect gutter down spouts in front of the French Drain.  The water coming off the roof causes suction in the French Drain Behind it.  This greatly increases the French Drains ability to move water without increasing the size of the French Drain Pipe.

Gutter Downspout Connected to 6 Inch French Drain

Recently we installed a French Drain inside the court yard of a rest home in Norman.  We had several interesting challenges to overcome that were not typical for a French Drain Installation.  The court yard was in the center of the home and was a secure area for the patrons.  We had to put down painters tarps to run our wheel barrows over.  We took out 44 loads of dirt and brought in 52 loads of Crushed one inch lime stone for the French Drain.  Each trip was over a hundred yards from the trailer in the parking lot, in the front door, down the hall, making two turns along the way.  Each time we had to be escorted by security.  Needless to say, the installation of this particular drainage system took a while.In the above picture, the French Drain runs along the low area crossing all the areas where water would stand each time it rained.

French Drain in Rest Home Courtyard

When a French Drain is installed, a big mistake that is made by many people is to cover up the gravel with dirt.  This is a big mistake.  Basically it is ” Putting the cork back in the bottle.”  If the French Drain is in full sun and has a type of grass surrounding it that spreads on its own such a ” Tift” or “Bermuda” , Grass will grow over it and the French Drain will eventually disappear.  Grass covering a French Drain is a good thing if it grows across the drain without adding dirt.  The Grass thatch acts a water filter preventing clogging and extending the life of the Drainage System.

When a French Drain is in Full Shade, or the surrounding grass will not spread on its own, such as with Fescue,  other steps must be taken.  One option is to just leave it alone.  If you don’t mind how it looks, it will drain a large amount of water for many years.  Many times a French Drain can be a landscaping focal point.  They can be dressed up with all kinds of Rocks and Stones and Plants.

 

Just like a home or a car, a Sprinkler System requires repair or adjustment from time to time.  We  take great pride in the Sprinkler Repair Services that we provide.  In almost 26  years of service, We have  has solved virtually every Sprinkler Repair Problem possible.  We solve Sprinkler Repair Problems that other companies can’t handle.  If you live in Oklahoma City and have Broken Sprinkler Heads, or if you live in Norman and have Leaking Sprinkler Valves, or if you live in Edmond and your Sprinkler Controller quit working, give us a call. or send us an e-mail.

Lawn Sprinkler Repair is one of our business focuses.   We can help with:

1. Sprinkler Controller Problems

2. Leaking Back-Flow Valves

3. Leaking Sprinkler Pipes

4.  Shorted or disconnected valve wires

5. Sprinkler Zones or Sprinkler Stations that won’t work

6. Broken Sprinkler Heads

The above are the most common problems that we deal with.

Oklahoma Drainage and Sprinkler Repair can help if you need to re-design your sprinkler system. If for example you are adding a swimming pool in your back yard, we can move the sprinkler heads and sprinkler pipes to fit the new dimensions of your yard. We can redesign or add-on to sprinkler systems where the home owners needs change.

 


French Drain Installation In Yukon

Oklahoma Drainage and Sprinkler Repair : Servicing all of Central and Western Oklahoma since 1993.

Standing Water on Your Driveway?  A Surface Drain set in concrete may be what you need. Or maybe you need a French Drain Running alongside your driveway instead.  Handling water problems is what we are good at.  If you need help, Oklahoma Drainage can provide the best solution for your unwanted water problems.

standing water

A good place for a French Drain

We just finished a 4 inch Drainage System in Yukon.  It was a complicated system to install.  It utilized 4 inch French Drain in the flower beds,  12 inch Surface Drains on the side of the house,  6 inch French Drain along the garage foundation with 2 Pop – Up Emitters in the back yard and 3 Curb Fittings in the front.    First we installed 4 inch French Drain in the flowerbeds on both sides of the front door.  We connected 4 inch solid Drain Pipe into the French Drain and ran them underside walk to the curb.  Next we cut the curb with a concrete saw and installed 3 curb outlets for 3 separate French Drains.

Next we installed 4 12 Inch Drain Basins with grates along both sides of the house continuing with Solid Drain Pipe to the Pop-Up Emitters on the back fence. Finally we completed the Drainage System by installing a long run of 6 inch French Drain down the side of the garage foundation.   Installing the French Drains in the flower beds was the most difficult and took the most time.  Each French Drain took over a ton of crushed limestone to fill the French Drain trench.  The Six inch French Drain took even more limestone.

 Oklahoma Drainage and Sprinkler Repair

Hey Oklahoma, We are expanding to service all of Western Oklahoma as well as Central Oklahoma.  If you live in Elk City, and need a French Drain, we can help.  If water is standing on your driveway in Clinton, Give us a call.  Duncan, Lawton, and Altus are all new areas of service for us.

Since 1993 Oklahoma Drainage and Sprinkler Repair has solved all types of standing water and drainage issues.  We install Drainage Systems that utilize French Drains, Surface, Drains, Channel Drains, and Sump Pumps depending on the customers needs.

If you have water in the wrong place , we can help!

We also have Decades of experience repairing all types of Lawn Sprinkler Problems.  Fixing broken sprinkler heads, sprinkler valve problems and controller trouble just to name a few things.

French Drains as part of a Drainage System – 

Many times people use the term ” French Drain” as general name for a Drain used in or around your home.  French Drains are designed to move a lot of water over a large flooded area.  They are also designed to take water in on the surface of the ground or below the surface of the ground.  This is very important if the water coming into the flooded area is moving through the ground or coming up from underneath.  ” Sub Surface Water Movement.”  The picture below is not a French Drain!

A French Drain looks like this

river rock french drain

A French Drain Can Handle Standing Water

A French Drain can take in water in a broad area.  It can move a much larger volume of water compared to a Surface Drain.  Also, it can move sub surface water moving into the area where a Surface Drain won’t move any water at all.

Surface Drains are designed to move surface water only on a smaller scale in confined areas.

Each solves specific drainage problems.  A Drainage System may use one or both together or even several using many types of drains.

Do you have standing water in a large area in your yard?  Typically this calls for a French Drain.  A French Drain is a great way to control standing water in a large grassy area.  It can also protect areas from flooding to a certain degree.  As long as the French Drains capacity to move water is not exceeded.  If the French Drains capacity is exceeded then water will stand in the drainage area until the rain stops and the drain has time to catch up.  A good way to prevent this is to install a bigger French Drain with a larger pipe.  The difference between a 3 inch French Drain and a 6 inch French Drain is huge.

Another way to beef up a French Drain is to connect gutter down spouts in front of the French Drain.  The water coming off the roof causes suction in the French Drain Behind it.  This greatly increases the French Drains ability to move water without increasing the size of the French Drain Pipe.

gutter connect to drain

Gutter Downspout Connected to 6 Inch French Drain

Recently we installed a French Drain inside the court yard of a rest home in Norman.  We had several interesting challenges to overcome that were not typical for a French Drain Installation.  The court yard was in the center of the home and was a secure area for the patrons.  We had to put down painters tarps to run our wheel barrows over.  We took out 44 loads of dirt and brought in 52 loads of Crushed one inch lime stone for the French Drain.  Each trip was over a hundred yards from the trailer in the parking lot, in the front door, down the hall, making two turns along the way.  Each time we had to be escorted by security.  Needless to say, the installation of this particular drainage system took a while.In the above picture, the French Drain runs along the low area crossing all the areas where water would stand each time it rained.

Rest home french drain

French Drain in Rest Home Courtyard

When a French Drain is installed, a big mistake that is made by many people is to cover up the gravel with dirt.  This is a big mistake.  Basically it is ” Putting the cork back in the bottle.”  If the French Drain is in full sun and has a type of grass surrounding it that spreads on its own such a ” Tift” or “Bermuda” , Grass will grow over it and the French Drain will eventually disappear.  Grass covering a French Drain is a good thing if it grows across the drain without adding dirt.  The Grass thatch acts a water filter preventing clogging and extending the life of the Drainage System.

When a French Drain is in Full Shade, or the surrounding grass will not spread on its own, such as with Fescue,  other steps must be taken.  One option is to just leave it alone.  If you don’t mind how it looks, it will drain a large amount of water for many years.  Many times a French Drain can be a landscaping focal point.  They can be dressed up with all kinds of Rocks and Stones and Plants.

 

Just what is a “French Drain?”  Many times people incorrectly

French drain installed
A French Drain can protect your foundation!

use the phrase, “French Drain,”  to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drain Pipe is connected underground to an outlet on the Drain Basin Storm-Water Drains through the grate into the Drain Basin.  Once in the Drain Basin, water travels out of the basin through a Drain Pipe.  The Storm-Water continues downhill in an underground Drain Pipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

A Channel Drain is a type of Surface Drain and many times is installed in concrete across sidewalks or driveways.

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench.  The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe.   This is to ensure that the Drain Pipe does not become clogged.

The dirt that was taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed.

A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.
The main downfall of a French Drain is that they, for the most part aren’t very pretty.  They don’t look very nice in a yard once they are completed.
Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the lime stone.  Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel.  This is Ok.  It won’t have a measurable effect on the performance of the drain.
DONT COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT.  THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT.  DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.

DECORATIVE STONE CAN BE USED TO COVER A FRENCH DRAIN AND THEY LOOK GREAT AND LAST A LIFETIME.

nice rock
French Drains Can Look Great!

 

Installing Cement around Curb Fitting for French Drain

Installing Cement around Curb Fitting for French Drain

 

A French Drain will move large amounts of water from the Drainage Problem Area to the Exit point.

A French Drain will Drain away water that gets to the Drainage Problem Area in 3 ways.

1.  Water gets to the problem area by falling from the sky.

2.  Water gets to the problem area by flowing down hill over the ground.

3.  Water gets to the problem area by flowing underground. (Sub-Surface water flow)

Number 3, Sub-Surface water flow is the big consideration.  When doing a Drainage Diagnostic, this is the area that is many times missed or not considered by less experienced companies.  Oklahoma  Drainage and Sprinkler Repair  relies on 26 years of experience.  Many Times it is cheaper and more effective to install a French Drain over a Surface Drain.  A Surface Drain can’t move as much water as a French Drain, and a Surface Drain can’t Drain away Sub-Surface waterSurface Drains should be installed in areas where the Drainage Problem area is smaller and is not affected by sub-surface water.

The draw back to a French Drain, is that it is not a pretty as a Surface Drain.

French Drains do a great job running along foundations and driveways.  A French Drain will keep water away from cement and prevent damage to concrete if water should freeze up against it.  A French Drain can keep your foundation Dry.

.


Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Providing Expert Sprinkler RepairBroken Sprinkler Pipes Sprinkler Head AdjustmentSprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.

French Drain Installation

Oklahoma Drainage and Sprinkler Repair has been diagnosing and solving Drainage Problems since 1993.  Water has the ability to get into places around your home where you really don’t want it to be.  Some drainage problems are easy to solve.  Typically water enters the problem drainage area one way from one source.  The really tricky drainage problems occur when water enters the problem drainage area from multiple directions and from multiple sources.  Sometimes a secondary water source can’t be seen or identified until the primary water problem source is eliminated.

An example of this occurs when water is running into a problem area in an obvious way over the ground where you can see it.

Simple enough.

A drainage system is installed with a surface drain as the “intake” with drainage pipe running to an exit point.  Initially the water drains away and everything looks great.  The next day water is back and is all around the surface drain, but below the edge and it hasn’t rained at all, so no additional water ran over the surface of the ground to flood the area.  The primary water source was solved, ( The surface water run off ) but the secondary water source was not.  Which was sub-surface water, (ground water) running into the area.  A surface drain can’t drain “ground water.”  A French Drain should have initially been installed instead of a Surface Drain.  A French Drain can drain both Surface Water and Ground Water.

 

river rock french drain install

A French Drain Can Handle Standing Water

 

Oklahoma Drainage and Sprinkler Repair installs a variety of other types of Drains.  Our Drainage Systems may utilize: French Drains, Surface Drains, Channel Drains, Trench Drains, Basin Drains, and Sump Pumps.  In the past 26 years, we have installed French Drains to keep water away from home and business foundations, Surface Drains to keep water away from sidewalks and driveways,  Trench Drains, and French Drains to keep standing water out of flowerbeds and yards, and Sump Pumps to remove water from basements and outdoor low lying areas.

Wow, Some Drainage Problems are tougher than others.  Had a customer in Chickasha with an unusual Drainage Problem.  She had a new Driveway installed.  The Cement work was nice enough but they left out one major consideration when installing the new Driveway.  Even after a small rain the water would run right down the driveway, under the Garage Door and directly into the Garage.  This was a bad problem that was about to get worse.  The first big rain came and everything was magnified.  The Rushing water took out the garage door and the back wall of the garage.  Yikes!!

Hmm,?  What to do?  The company that installed the Driveway was nowhere to be found.  No surprise.

The water volume was huge and the customer had no means to redo the driveway which was substantial.

The solution took a little “Out Of The Box Thinking”.

We Installed an 8 inch metal channel drain grate across the driveway.  But with no channel drain underneath.  A large channel drain could not handle the water volume that we were dealing with.  Instead of installing a channel drain underneath the grate, we cut completely through the driveway concrete and installed two 6 inch French Drains stacked on top of each other underneath the Channel Drain Grate.

This took place in July of 2017.  Since then not a drop of water has reached the garage.

We put two French Drains under a larger version of a drain that looks like the above picture.

Drainage Systems can be made up of one drain or a combination of many drains.  Drainage  problems can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together.  Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together.

An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional Surface Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street.

A simple Drainage System might consist of a Surface Drain that is connected to a second Surface Drain which runs to a Pop-up Emitter which lets water drain over the curb and into the street.

An “Exit Point” is the term used for where all the water leaves the Drainage System.  Determining the Exit Point is very critical.  It is one of the first things we do when diagnosing a Drainage Problem.

French Drain with stepping stones

French Drain with stepping stones

 

French Drains can be installed by themselves, or as part of a Drainage System that uses other French Drains, Surface Drains, or other Drain combinations.  Typically a French Drain is used to protect a broad area that has a lot of standing water.  A French Drain might run along side a homes foundation, or beside a driveway, or on any Drainage Project where Sub-Surface water is the primary problem.  If water is running toward your home under ground ( through sandy soil), A French Drain is the only Solution  for draining away water flowing under ground.

 

If you live in Oklahoma City and need a French Drain installed in your yard, or along your driveway, or near your foundation, give Give us a call.  If you live in Edmond or Norman and need a Surface Drain installed in the concrete in your sidewalk or driveway, we can help.  If you live in Mustang or Yukon and would like to protect your trees or flower beds from standing water with a French Drain,

 

 

Cutting The Curb and Installing Curb Fitting for French Drain

Cutting The Curb and Installing Curb Fitting for French Drain

 

Every time it rains, do you have standing water on your driveway, sidewalk, or even LEAKING INTO YOUR HOUSE?  If you need DRAINAGE SOLUTIONS,  WE can help!  We specialize in: French Drains, Surface Drains, Channel Drains, Basement Drains, Trench Drains, Basin Drains, and Sump Pumps.

Problem Drainage Area

This Area Needs a French Drain!

 


Oklahoma Drainage had a customer in Lawton with water in their floor vents.  Every time the heater would run, it would spit water out of the vents.  Water was seeping through the foundation and into the ducts.  Cold water and warm air can cause mold to develop.  After a good duct cleaning company got all the water out, we went to work.  We installed a 6 inch French Drain three feet from of the foundation across the entire width of the house.  It intercepted all the surface water running down the hill.  More importantly it caught and stopped all the sub surface water traveling underground through the sandy soil.  The floor ducts stayed dry!

Oklahoma Drainage also installs a variety of other types of Drains.  Our Drainage Systems may utilize: French Drains, Surface Drains, Channel Drains, Trench Drains, Basin Drains, and Sump Pumps.  In the past 26 years, we have installed French Drains to keep water away from home and business foundations, Surface Drains to keep water away from sidewalks and driveways,  Trench Drains, and French Drains to keep standing water out of flowerbeds and yards, and Sump Pumps to remove water from basements and outdoor low lying areas.

French Drain with stepping stones

French Drain with stepping stones

 

French Drains can be installed by themselves, or as part of a Drainage System that uses other French Drains, Surface Drains, or other Drain combinations.  Typically a French Drain is used to protect a broad area that has a lot of standing water.  A French Drain might run along side a homes foundation, or beside a driveway, or on any Drainage Project where Sub-Surface water is the primary problem.  If water is running toward your home under ground ( through sandy soil), A French Drain is the only Solution  for draining away water flowing under ground.

 

If you live in Oklahoma City and need a French Drain installed in your yard, or along your driveway, or near your foundation, give CMG a call.  If you live in Edmond or Norman and need a Surface Drain installed in the concrete in your sidewalk or driveway, we can help.  If you live in Mustang or Yukon and would like to protect your trees or flower beds from standing water with a French Drain, We specialize in just that!

 

 

For most of us our home or business is our most important investment.  Standing Water can cause damage to what is important to us.  High Water from Storm-Water Runoff deteriorates concrete and cement.  This means that our driveways, sidewalks, and foundations need protection from prolonged exposure to Standing Water.  (Not to mention damage to plants, trees, and grass) WE have have been solving Drainage Problems since 1993.  If you live in Central Oklahoma we can quickly provide a free estimate.