6 Inch French Drain Installation, Oklahoma City, Norman, Moore, Yukon

Six inch French Drain Installation, Oklahoma City, Norman, Moore, Yukon.  

Oklahoma Drainage, Servicing all of Central and Western Oklahoma since 1993.

Installing a Large 6 Inch Curb Outlet For a French Drain

Edmond is one of the communities in Central Oklahoma that Oklahoma Drainage  services.  We have installed almost a thousand French Drains in the Edmond community in the past 21 years.  Edmond has many hills and valleys.  Many Neighborhoods are built on hillsides.  This causes many Drainage Problems.  We have installed French Drains by themselves and as a part of Drainage Systems to protect Driveways, Sidewalks, Foundations all over Edmond.  French Drains may be installed in Flower Beds or grassy areas too.  French Drains when installed correctly can provide many years of property protection and Piece of Mind.

French Drain in Oklahoma City

Here is a description of other recent work.

A little bit North of Downtown Oklahoma City,  Oklahoma Drainage installed a 6 inch French Drain between two businesses which were less than three feet apart.  The French Drain went between a Law Firm and a Tire shop.  Water was leaking through the walls of both businesses.  Gutters between the two establishments were dumping a huge amount of water.  We installed a 6 inch French Drain between the two.

French Drain connected to gutter

It took a long time to get the dirt out of the trench for the French Drain.  It was a very tight fit.  We had to use a little red wagon to haul out the dirt for the French Drain and haul back in the crushed limestone for the French Drain.  It looked a little silly, but it was the only thing we could find that was narrow enough to fit between the buildings.  A French Drain that normally would take 1 day to install took three.

Curb Outlet for French Drain

The French Drain had a Double Exit Point.  This means that once water entered the French Drain Pipe, it could run South to the street or it could run North to the alley.  To exit points greatly increases the water capacity for any French Drain.

Along the course of the French Drain, we connected two large gutters directly into the Drain Pipe.

Once in place, the French Drain eliminated all the water that was leaking into the two buildings.

Drainage Problem Solved!

 

 

UNDERSTANDING DRAINAGE SYSTEM TERMINOLOGY

If you have a problem with standing water or have water getting into a place that it shouldn’t be, causing damage and stress, A Drainage System is needed to solve your problem.

First you must understand that your own observations determine the Drainage System Design. You need to be comfortable with Drainage Terminology.

There are 2 basic categories of Drainage Systems.

1. Standard Drainage Systems
2. Flood Prevention Systems

A Standard Drainage System is a System that Drains away water after it enters the Problem Drainage Area. Once in the area the water is drained away over time. The better the Drainage System, the faster and more completely the water is removed.

A Flood Prevention System is a Drainage System that intercepts water before it ever enters the Problem Drainage Area. Flood

Prevention Systems typically are more robust.  They must have larger pipes or more pipes to handle extreme flooding.  

There may be situations where Drainage Systems or Flood Prevention Systems fail due to extreme flooding.  A flood may put the Exit point of the Drainage System under water.  If your entire property is under water, nothing will drain until the flood goes away.

With that being said, Your Drainage System may be in a location that it is impossible to flood or very unlikely.

So, Step one is to decide,” Do I want a Standard Drainage System? OR, Do I want a Flood Prevention System?”

French Drain Intake

The next consideration is the Design of your drainage system.  Do you need a French Drain or a Surface Drain? Maybe you need both!

Channel Drain Installation

A Channel Drain is one of many types of Surface Drains.

Drain Grate

Norman Oklahoma French Drain, Norman Oklahoma French Drain Repair, Drain Repair, Drain Installation

Norman Oklahoma French Drain, Norman Oklahoma French Drain Repair, Drain Installation

Oklahoma Drainage 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

   

Drainage Systems, French Drains, Surface Drains, Channel Drains, Sump Pumps, Sprinkler Repair, with 30 years of experience. 

 

Just what is a “French Drain?” Many times people incorrectly

A French Drain can protect your foundation!

use the phrase, “French Drain,” when they mean “Surface Drain” or “Channel Drain.”

French Drain Installation is what we specialize in.  Since 1993 we have installed over 2000 French Drains or Drainage Systems in Oklahoma.

Curb Outlet for French Drain

Oklahoma Drainage 

French Drain Under River Rock

 

Channel Drain Installation

 

Drainage System Installation in Norman

Just what is a “French Drain?”  Many times people incorrectly.  A French Drain can protect your foundation!

use the phrase, “French Drain,”  to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drain Pipe is connected underground to an outlet on the Drain Basin. Storm-Water Drains through the grate into the Drain Basin.  Once in the Drain Basin, water travels out of the basin through a Drain Pipe.  The Storm-Water continues downhill in an underground Drain Pipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

Surface Drain connected to a Transition Pipe

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.Surface Drain and Drain Pipe

A Channel Drain is a type of Surface Drain and many times is installed in concrete across sidewalks or driveways.Channel Drain

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench.  The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe.   This is to ensure that the Drain Pipe does not become clogged.

The dirt that was taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed. A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it. The main downfall of a French Drain is that they, for the most part aren’t very pretty.  They don’t look very nice in a yard once they are completed.Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the lime stone.  Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel.  This is Ok.  It won’t have a measurable effect on the performance of the drain. DON’T COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT.  THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT.  DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.

DECORATIVE STONE CAN BE USED TO COVER A FRENCH DRAIN AND THEY LOOK GREAT AND LAST A LIFETIME.

Installing Decorative French Drain

French Drains Can Look Great!

Completed Decorative French Drain

Time for a French Drain, Installation, Oklahoma City, Norman, Edmond, Moore

French Drain Installation, Oklahoma City, Norman, Moore, Edmond

Oklahoma Drainage and Sprinkler Repair — 405 203 9419- Servicing all of Central and Western Oklahoma

FRENCH DRAIN, SURFACE DRAIN PHOTOS AND INFORMATION    Standing water can cause many types of property damage ranging from foundation problems to cracked sidewalks and dead plants and shrubs.  If you have need of French Drain or Surface Drain, give us a  call.  We provide free estimates for all of central Oklahoma.  

 

Connecting Gutter to French Drain

French Drain With Colored Gravel in Oklahoma City

Two French Drains coming together

Oklahoma Drainage and Sprinkler Repair 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

   

Oklahoma Drainage and Sprinkler Repair Installs Surface Drains and French Drains.  Some times it is up hill in all directions from the Problem Drainage Area.  This problem can be solved by installing a Sump Pump.  When the cavity fills, the water is pumped away to the point where the water exits the drain which can be a curb outlet or a pop-up emitter.

Sump Pump Installation

 

Curb outlet with more than 6 inches of fall

French Drain Running Through Low Areas

WHAT SIZE DRAIN PIPE FOR FRENCH DRAINS?

Installing Cement around Curb Fitting for French Drain in Norman

Some Drainage Systems are complex and incorporate several types of drains.  Most Drainage Systems , however are basic and require just one type of Drain.  Oklahoma Drainage and Sprinkler Repair installs a variety of drains to solve a variety of problems. French Drains, Surface Drains, and Channel Drains are most commonly used.  If you live in Edmond and need a Channel Drain installed across your driveway, or if you live in Norman and need a French Drain in your backyard, or if you live in Oklahoma City and need a Surface drain installed next to your sidewalk, we can help. Oklahoma Drainage and Sprinkler Repair provides Drainage Diagnostics .  A Drainage Diagnostic is a scheduled appointment where we come out and look at your Drainage Problem and get your input on the situation.  We look at all the variables that are causing your Water-Runoff Problems and design a Drainage System to solve it.  French Drains and Surface Drains are used to make up the Drainage System.

Setting the concrete around the channel drain

Channel Drain Installation in sidewalk in Oklahoma City

Typically many things must be considered when completing a Drainage Diagnostic.

1.  Identify the areas being damaged by water and determine if there are any hidden areas.

2.  Identify the sources of water causing the damage.  Most Drainage Problems have more than one source.  A water source can fall from the sky as rain, or can flow down the hill as storm-water runoff, or can flow from a gutter down-spout (yours or your neighbor’s),  or flow under ground as sub-surface water flow, or water can flow off a sidewalk, driveway, or street.  (These are the most common)

3.  Identify the Exit Point by determining where we want to take the unwanted water.

4.  Determine what type of Drains can best solve the Drainage Problem.  We utilize: French Drains, Surface Drains, Channel Drains, Trench Drains, and Sump Pumps.

5.  Determine what type and size of Drain Pipe is needed to accommodate the volume of water to be drained.  Larger is always better!  Big Drains with Small Drain Pipes never works!

If you have problems with Standing Water after a hard rain, or your driveway or sidewalk turns into a moat after a thunderstorm, or worst of all, you have water standing against your foundation and seeping into your house and vents, Give us a Call!  TYPICALLY A DRAINAGE SYSTEM IS MUCH LESS EXPENSIVE THAN FOUNDATION REPAIR OR REMOVING MOLD FROM YOUR HOME OR BUSINESS!!

Drainage System Installation in Norman

French Drain Installation in Oklahoma City, French Drain Repair in Oklahoma City, Norman, Edmond, Yukon

French Drain or Surface Drain?

So you have water in a place in your home or business that is causing a problem.  Maybe you have water standing on your sidewalk or leaking into your air conditioning ducts.  You might have water running under your garage door and flooding your garage.  You might have standing water that kills grass or plants in your yard.  There are an endless number of possible water drainage issues.

Oklahoma Drainage and Sprinkler Repair has provided solutions for water drainage problems since 1993.

We utilize French Drains and many types of Surface Drains to solve all types of Residential and Small Business water problems.  We also install Sump Pumps when water can not be drained from the problem area.

As of January 2021 we have provided service for 5467 customers in Oklahoma.  Our service area includes all of Central and Western Oklahoma.  We will service other areas of Oklahoma by special appointment.

There is never any cost for us to come and look at your water problems.

Give us a call for a free Estimate at 405 203 9419 or E-Mail — frenchdrain.sprinklerrepair@gmail.com

Setting the concrete around the channel drain

French Drain Installation in Edmond

• 

  French Drain Running on the side of the house

• 

• 

Putting limestone on top of french drain

French Drain Pipe running to curb outlet in Oklahoma City.

The Drain Pipe used by Oklahoma Drainage consists of: ADS Perforated with Soc Drain Pipe,  ADS Solid Drain Pipe, Sewer and Drain– Drain Pipe,  PVC 40 schedule used as Drain Pipe,  200 Class PVC used as Drain Pipe.  Using a variety of Drain Pipe and Drains allow us to address Drainage Problems that range from simple to complex and from standard to unique.

Standing water comes from many sources.  It causes damage to  sidewalks, driveways, and foundations not to mention plants, trees, and  grass.  Does the side of your house flood because your neighbor doesn’t  have gutters, or does your sidewalk turn into a moat after a heavy rain,  or worst of all, does water seep into your foundation and duct work  after a thunderstorm.  Theses are just a few of the Drainage  Problems that we  can help with.A French Drain can protect your foundation!

Oklahoma City French Drain, Oklahoma City French Drain Repair, French Drain in Oklahoma City, Information

A NEW FRENCH DRAIN IN OKLAHOMA CITY

Recently we installed a large Drainage System in OKC.  It was a 4 inch System using 4 inch ADS French Drain Pipe with Soc and 4 inch ADS Solid Drain Pipe.  The “Intake” of the Drainage System had two parts.  Water from the gutters on the house was fed into the Drainage System.  There were 7 gutter downspouts around the entire house that were connected straight into the Drainage System with Solid Drain Pipe and a Gutter connection.

French Drain Installation

The area in the picture above stayed wet and muddy all the time and grass would not grow.  This is a picture 4 months after installation of a 4 inch French Drain with Trench liner and Pipe filter.

 

French Drain Installation In Yukon

Oklahoma Drainage  : Servicing all of Central and Western Oklahoma since 1993.

Standing Water on Your Driveway?  A Surface Drain set in concrete may be what you need. Or maybe you need a French Drain Running alongside your driveway instead.  Handling water problems is what we are good at.  If you need help, Oklahoma Drainage can provide the best solution for your unwanted water problems.

 

A good place for a French Drain

French Drain keeps water off of sidewalk

We just finished a 4 inch Drainage System in Yukon.  It was a complicated system to install.  It utilized 4 inch French Drain in the flower beds,  12 inch Surface Drains on the side of the house,  6 inch French Drain along the garage foundation with 2 Pop – Up Emitters in the back yard and 3 Curb Fittings in the front.    First we installed 4 inch French Drain in the flowerbeds on both sides of the front door.  We connected 4 inch solid Drain Pipe into the French Drain and ran them underside walk to the curb.  Next we cut the curb with a concrete saw and installed 3 curb outlets for 3 separate French Drains.

French Drain Installed in Yukon

Next we installed 4 12 Inch Drain Basins with grates along both sides of the house continuing with Solid Drain Pipe to the Pop-Up Emitters on the back fence. Finally we completed the Drainage System by installing a long run of 6 inch French Drain down the side of the garage foundation.   Installing the French Drains in the flower beds was the most difficult and took the most time.  Each French Drain took over a ton of crushed limestone to fill the French Drain trench.  The Six inch French Drain took even more limestone.

 Oklahoma Drainage and Sprinkler Repair –

Hey Oklahoma, We are expanding to service all of Western Oklahoma as well as Central Oklahoma.  If you live in Elk City, and need a French Drain, we can help.  If water is standing on your driveway in Clinton, Give us a call.  Duncan, Lawton, and Altus are all new areas of service for us.

Since 1993 Oklahoma Drainage and Sprinkler Repair has solved all types of standing water and drainage issues.  We install Drainage Systems that utilize French Drains, Surface, Drains, Channel Drains, and Sump Pumps depending on the customers needs.

If you have water in the wrong place , we can help!

We also have Decades of experience repairing all types of Lawn Sprinkler Problems.  Fixing broken sprinkler heads, sprinkler valve problems and controller trouble just to name a few things.

French Drains as part of a Drainage System – 

Many times people use the term ” French Drain” as general name for a Drain used in or around your home.  French Drains are designed to move a lot of water over a large flooded area.  They are also designed to take water in on the surface of the ground or below the surface of the ground.  This is very important if the water coming into the flooded area is moving through the ground or coming up from underneath.  ” Sub Surface Water Movement.”  The picture below is not a French Drain!

 

Connecting Gutter to French Drain

Oklahoma Drainage  installs a variety  of Drains.  Our Drainage Systems may utilize: French Drains, Surface Drains, Channel Drains, Trench Drains, Basin Drains, and Sump Pumps.  In the past 21 years, we have installed French Drains to keep water away from home and business foundations, Surface Drains to keep water away from sidewalks and driveways,  Trench Drains, and French Drains to keep standing water out of flowerbeds and yards, and Sump Pumps to remove water from basements and outdoor low lying areas.

French Drain with stepping stones

French Drains can be installed by themselves, or as part of a Drainage System that uses other French Drains, Surface Drains, or other Drain combinations.  Typically a French Drain is used to protect a broad area that has a lot of standing water.  A French Drain might run along side a homes foundation, or beside a driveway, or on any Drainage Project where Sub-Surface water is the primary problem.  If water is running toward your home under ground ( through sandy soil), A French Drain is the only Solution  for draining away water flowing under ground.

6 Inch French Drain

If you live in Oklahoma City and need a French Drain installed in your yard, or along your driveway, or near your foundation, give Oklahoma Drainage a call.  If you live in Edmond or Norman and need a Surface Drain installed in the concrete in your sidewalk or driveway, we can help.  If you live in Mustang or Yukon and would like to protect your trees or flower beds from standing water with a French Drain,

Installing wet concrete around channel drain

Channel Drain Installation in Sidewalk

OKLAHOMA CITY FRENCH DRAIN REPAIR, OKLAHOMA CITY FRENCH DRAIN

Oklahoma is famous for it’s powerful thunderstorms and heavy downpours. Storm-water runoff causes a variety of DRAINAGE PROBLEMS for Home and Business owners.

This front yard needs a french drain!

DRAINAGE PROBLEMS come in a wide variety of forms. You might have water standing in your backyard after a thunderstorm. Water from your gutter-downspouts may be turning your sidewalk into a “Moat.” Or, worst of all, Standing Water may be seeping into your home. WE can help!

Drainage solutions sometime require one or several types of drains to solve the problem. Oklahoma Drainage  has been successfully solving DRAINAGE PROBLEMS since 1993. We can quickly diagnose your DRAINAGE PROBLEM and design a DRAINAGE SYSTEM to solve your DRAINAGE PROBLEMS. WE UTILIZE: FRENCH DRAINS, SURFACE DRAINS, CHANNEL DRAINS, BASIN DRAINS, TRENCH DRAINS, BASEMENT DRAINS, AND SUMP PUMPS.

Sump Pump connected to french drain

 

Connecting Gutter to French Drain

 

Curb outlet with more than 6 inches of fall

 

 

 

 

Drainage System Installation in Norman

 

 

Standing water comes from many sources.  It causes damage to sidewalks, driveways, and foundations not to mention plants, trees, and grass.

Does the side of your house flood because your neighbor doesn’t have gutters, or does your sidewalk turn into a moat after a heavy rain, or worst of all, does water seep into your foundation and duct work after a thunderstorm.  Theses are just a few of the Drainage Problems that Oklahoma Drainage can help with.

Just what is a “French Drain?”  Many times people incorrectly use the phrase, “French Drain,”  to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drain Pipe is connected underground to an outlet on the Drain Basin.  Storm-Water Drains through the grate into the Drain Basin.  Once in the Drain Basin, water travels out of the basin through a Drain Pipe.  The Storm-Water continues downhill in an underground Drain Pipe to an exit point.

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

 

A Channel Drain is a type of Surface Drain and many times is installed in concrete across sidewalks or driveways.

Channel Drain

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench.  The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe.   This is to ensure that the Drain Pipe does not become clogged.

The dirt that was taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed.

French Drain

A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it. The main downfall of a French Drain is that they, for the most part aren’t very pretty.  They don’t look very nice in a yard once they are completed.Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the lime stone.  Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel.  This is Ok.  It won’t have a measurable effect on the performance of the drain.  DONT COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT.  THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT.  DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.

 

Oklahoma City Channel Drain Across Driveway

 

Oklahoma Drainage and Sprinkler Repair

French Drain Installation is a primary focus fore Oklahoma Drainage and Sprinkler Repair.  We have been installing French Drains as part of Drainage Systems since 1993.   We also install Surface Drains, Channel Drains, and Sump Pumps to fit our customers needs.

Setting the concrete around the channel drain

A Drainage System is made up of three parts.  An Intake, a transition, and and Exit.

An intake is a Drain or a group of Drains that brings water into the Drainage System.  It can be a French Drain, Surface Drains, Channel Drain, or Sump Pump.  A Drainage System can have one intake or several.  If more than one, it can be any combination of French Drains, Surface Drains, Etc.

For Example: You might have a Surface Drain set in your sidewalk and a Channel Drain next to your driveway and a French Drain in your yard.  They all connect to each other through drain pipe and feed water into the Drainage System.

The Transition is the Drain Pipe that takes the water to the exit point.  It can be a large pipe or small depending on how much water needs to be moved and how fast it needs to drain.  More than one Drainage Exit Point.  This increases the amount of water that the Drainage System can move.

There are other things to take into account and consider as well.

French Drain installed under walkway

 

French Drain Installed in Lawton

 

Oklahoma Drainage and Sprinkler Repair installs French Drains and Surface Drains in lawns, flower beds and many other places.  We also install Surface Drains and Channel Drains Set in concrete in sidewalks and driveways.  Wherever you need a Drain to help protect your home or property, we are there to help.  Experience Counts, going on 27 years now.

Oklahoma Drainage and Sprinkler Repair 405 203 9419 — We provide:

    French Drain Installation, Surface Drain Installation, Drainage System Installation

    Sprinkler Repair for all aspects of Residential Sprinkler Systems

    Emergency Sprinkler Repair Service, AFTER HOURS AND WEEKENDS.

Drainage Systems, French Drains, Surface Drains, Channel Drains, Sump Pumps, Sprinkler Repair, with 26 years of experience. 

French Drain Installation under walkway

Completed French Drain under walk way

Just what is a “French Drain?” Many times people incorrectly Harsh weather in Oklahoma seems to becoming more common.  In 2013,  Norman Oklahoma had 4 inches of rain in two hours.  That’s the most rain in a short time that I can remember.  Storm-Water runoff can cause damage to all types of property and buildings.  Water getting inside your house is never a good thing.  A Drainage System that utilizes a French Drain can help.

French Drain around curve

French Drain keeps water off of sidewalk

Drains can protect your home and property from water damage. Large 6 Inch French Drain Installed in Norman

Drainage Systems can be made up of one drain or a combination of many drains.  Drainage  problems can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together.  Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together.

An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional Surface Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street.

Sump Pump Installation

A simple Drainage System might consist of a Surface Drain that is connected to a second Surface Drain which runs to a Pop-up Emitter which lets water drain over the curb and into the street.

An “Exit Point” is the term used for where all the water leaves the Drainage System.  Determining the Exit Point is very critical.  It is one of the first things we do when diagnosing a Drainage Problem.

Gutter Connected to French Drain

French Drain using River Rock

 

French Drain In Norman, Information, French Drain Photos, French Drain Tips

Harsh weather in Oklahoma seems to becoming more common.  In 2013,  Norman Oklahoma had 4 inches of rain in two hours.  That’s the most rain in a short time that I can remember.  Storm-Water runoff can cause damage to all types of property and buildings.  Water getting inside your house is never a good thing.  A Drainage System that utilizes a French Drain can help.

French Drain keeps water off of sidewalk

Drains can protect your home and property from water damage. Large 6 Inch French Drain Installed in Norman

Drainage Systems can be made up of one drain or a combination of many drains.  Drainage  problems can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together.  Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together.

An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional Surface Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street.

Sump Pump Installation

A simple Drainage System might consist of a Surface Drain that is connected to a second Surface Drain which runs to a Pop-up Emitter which lets water drain over the curb and into the street.

An “Exit Point” is the term used for where all the water leaves the Drainage System.  Determining the Exit Point is very critical.  It is one of the first things we do when diagnosing a Drainage Problem.

Connecting Gutter to French Drain

Drainage Systems can:

1.  Keep water away from foundations — A French Drain is best because it can move Surface Water and Sub-Surface Water (water moving under ground) away from the foundation.  Many times less experienced companies install Surface Drains to keep water away from foundations.  This can be a big mistake.  A Surface Drain can’t move or drain Sub-Surface Water.   Also A Surface Drain often can’t move enough water fast enough and easily becomes overwhelmed during a heavy rain.  A Surface Drain also can’t cover or protect a broad enough area. Surface Drains should be designed in a Drainage System to be located in smaller Drainage Areas moving moderate amounts of water.  Surface Drains look better than French Drains.  If ,”appearance” is more important than Drainage Capacity, Go with the Surface Drain.  Just know what you are getting into and what your expectations should be. One side of a foundation alone,  can be over 100 feet.  A 4 inch or 6 inch French Drain is best when protecting a large area such as a foundation.Surface Drain Installed next to sidewalk in Oklahoma City.

Gutter Connected to Drain

2.  Keep water away from small or enclosed areas.  This might be a low area just through a gate on the side of a house, or the low area between a flowerbed and the wall of a house, or standing water on or near a sidewalk or driveway.  These types of Drainage Problems are best served with Surface Drains.  A Surface Drain can move water away from a low area that is relatively small.  This can occur in yards, flowerbeds, sidewalks and driveways.  A Surface Drain is designed to move Surface Water away from a problem area to a predetermined exit point.  Surface Drains are available in many sizes.  How quickly they remove standing water is usually determined by the size of the Drain Pipe that is connected to the Drain.Surface Drain Installation in Norman

Simply put, a Drainage System is one or a group of underground Drain Pipes that take water away from a place that has water standing on it or flowing across it.  The water that is in the problem area, can be causing damage or may be inconvenient or both.  (Usually Both)  A simple Drainage System is a Drain for the water to enter, a Drain Pipe to move the water away from the Drain, and an Exit Point for the water to be released out of the Drain Pipe.

Drainage Systems quickly can become more complicated.  Considerations must include:

How does the water get to the problem area?  There may be one or many sources.

Water Sources:

1.  It falls from the sky directly

2.  It flows down hill over the surface (surface water)

3.  It flows underground under the surface (sub-surface water)

4.  It flows from the edge of a roof ( There may be many roofs near the problem area, neighbors etc.)

5.  It flows from a gutter downspout

6.  It flows over the edge of a gutter because the gutter is too small is is clogged

7.  It flows up from the ground (seeps and springs are common in Oklahoma)

8.  It flows from a sprinkler system use ( yours or your neighbors)

9.  It flows from a leaking pipe ( water mains, water meters, water lines, sprinkler pipes, sprinkler valves)

There are other reasons for Drainage Problems, the above reasons are just the most common.

Once the number of water sources is determined, a rough estimate of the amount of water that needs to be drained away on average must be estimated.  This can be simplified down to “SMALL, MEDIUM, OR LARGE AMOUNTS OF WATER TO BE DRAINED AWAY.  You don’t have to be an engineer trying to calculate fluid dynamics.  Experience at diagnosing drainage problems helps however.  How much water needs to be moved will help determine the type and size of the Surface Drain or French Drain that needs to be installed.  It also helps to determine the size of Drain Pipe required for the Drainage System.  A good rule to follow is, “If in doubt, install a larger Drain and Drain Pipe.”  Unused Drainage Capacity is better than property damage caused by a Drain that is overwhelmed by too much water.

For home and small business use typical materials used are:

6 inch, 9 inch, and 12 inch Surface Drains –

3 inch, 4 inch, and 6 inch Drain Pipes —

3 inch, 4 inch, and 6 inch French Drains —

French Drains move more water than Surface Drains —

French Drains move Surface Water and Sub-Surface Water

Surface Drains move Surface Water only

Surface Drains look nicer than French Drains in most cases

Once the type and number of drains is determined and what size Drain Pipe will connect them, an exit point must be selected.  (Where is the Drainage System going to take the water to and release it?)

The Drainage Curb Fitting is installed when the desired exit point for the French Drain will release the Drainage Water into the Street.   The Drainage Curb Fitting is rectangular in shape and made to be installed through the curb.  A small section of Curb is cut out with a concrete saw.  The Section is a few inches wider than the Drainage Curb Fitting.  We then install new concrete around the curb fitting.  Once the concrete has dried, the Drain Pipe coming from a French Drain or Surface Drain is connected to the Drainage Curb fitting and then covered with dirt.Cutting The Curb and Installing Curb Fitting for French Drain

The Drainage Pop-Up Emitter is connected to the end of a Drain Pipe.  It is downhill from a French Drain or a Surface Drain.  It is a small release basin with a green pop-up lid.  When releasing water, it pops up about an inch to release the water from the French Drain or Surface Drain.  When the Storm Water has moved through the Drainage System and out of the Pop-Up Emitter, the green lid closes back to its original closed position.  The emitter is designed to release water out into a yard or down a hill or other desirable Drainage Exit Point where there is no curb.Popup Emitter to release water from a Drainage System in Yukon.

Drainage System installation and design is a big part of our business.  Does your sidewalk turn into a moat after a hard rain?Does part of your yard look like a pond after a thunderstorm?Worst of all, are you experiencing concrete deterioration to your foundation, sidewalk, or driveway.  Oklahoma Drainage can design a Drainage System to solve your Drainage Problems.  Our Drainage Systems can be simple or complex.We utilize, French Drains, Surface Drains, Channel Drains, Basin Drains, Basement Drains, Trench Drains, and Sump Pumps.  Estimates are free

Oklahoma City French Drain, French Drain Repair Oklahoma City, Drain Installation

Oklahoma Drainage and Sprinkler Repair — Installing – French Drains – Surface Drains – Channel Drains – Sump Pumps

Providing Expert Sprinkler Repair – Broken Sprinkler Pipes – Sprinkler Head Adjustment – Sprinkler Valve Replacement

Servicing all of Central and Western Oklahoma since 1993.

French Drains as part of a Drainage System – 

Many times people use the term ” French Drain” as general name for a Drain used in or around your home.  French Drains are designed to move a lot of water over a large flooded area.  They are also designed to take water in on the surface of the ground or below the surface of the ground.  This is very important if the water coming into the flooded area is moving through the ground or coming up from underneath.  ” Sub Surface Water Movement.”  The picture below is not a French Drain!

Surface Drain

A French Drain looks like this

Recently Oklahoma Drainage and Sprinkler Repair Installed a French Drain as part of a Drainage System in Mid West City Oklahoma.

Our customer had a back porch Sun Room.  Every time he had a hard rain, Water would run in one door and out the other.  An indoor creek across his Sun Room.

French Drain keeps water off of sidewalk

We installed a French Drain in front of the South Door.  It was 26 feet long and ran from a gutter downspout which it was connected to,  in front of the South Door and along the house covering the entire “Low” Area.  Then we connected 4 inch ADS Solid Drain pipe to the French Drain and ran down hill around the corner of the house to the street.

French Drain pipe running to street

Once the 4 inch solid drain pipe was connected to the French Drain and the two gutter down spouts, a pop-up emitter was installed to release the water at the street.

The next step was to cover the drain pipe with dirt and put the sod back in place on top of the pipe.   There was about 8 wheelbarrows of dirt left over that was displaced by the drain pipe and the French Drain.  The extra dirt was scooped up and hauled away.

While installing the drainage system, it was necessary to move two sprinkler heads that were in the way of the drain pipe installation.  This was no problem.  Installing drainage systems and French drains for folks who have a sprinkler system is very common.  Moving Sprinkler heads or pipes sometimes is necessary.  We always leave the sprinkler system in complete working order and we discuss any changes in the sprinkler system with the customer before we do it to make sure that everyone is on the same page.  In most cases the customer cant tell that we made any changes to the sprinkler system at all.

Drainage System Installation in Norman

Harsh weather in Oklahoma seems to becoming more common.  In 2013,  Norman Oklahoma had 4 inches of rain in two hours.  That’s the most rain in a short time that I can remember.  Storm-Water runoff can cause damage to all types of property and buildings.  Water getting inside your house is never a good thing.  A Drainage System that utilizes a French Drain can help.

Drains can protect your home and property from water damage.

Large 6 Inch French Drain Installed in Norman

Drainage Systems can be made up of one drain or a combination of many drains.  Drainage  problems can be very complex.   Complex Drainage Problems may require a combination of several different types of drains all inter-connected and working together.  Other times the drainage problem may be simple and straight-forward requiring only one drain or several of the same type of drain connected together.

An example of a complex drainage system would be:  A French Drain in the back yard connected to a Surface Drain near a flower bed connected to several gutter downspouts, which are connected to a Channel Drain going across a driveway, which is connected to additional Surface Drain in the front yard, which runs to a Curb Fitting that lets all the water drain out on to the street.

A simple Drainage System might consist of a Surface Drain that is connected to a second Surface Drain which runs to a Pop-up Emitter which lets water drain over the curb and into the street.

An “Exit Point” is the term used for where all the water leaves the Drainage System.  Determining the Exit Point is very critical.  It is one of the first things we do when diagnosing a Drainage Problem.

Drainage Systems can:

1.  Keep water away from foundations — A French Drain is best because it can move Surface Water and Sub-Surface Water (water moving under ground) away from the foundation.  Many times less experienced companies install Surface Drains to keep water away from foundations.  This can be a big mistake.  A Surface Drain can’t move or drain Sub-Surface Water.   Also A Surface Drain often can’t move enough water fast enough and easily becomes overwhelmed during a heavy rain.  A Surface Drain also can’t cover or protect a broad enough area. Surface Drains should be designed in a Drainage System to be located in smaller Drainage Areas moving moderate amounts of water.  Surface Drains look better than French Drains.  If ,”appearance” is more important than Drainage Capacity, Go with the Surface Drain.  Just know what you are getting into and what your expectations should be. One side of a foundation alone,  can be over 100 feet.  A 4 inch or 6 inch French Drain is best when protecting a large area such as a foundation.

Surface Drain Installed next to sidewalk in Oklahoma City.

2.  Keep water away from small or enclosed areas.  This might be a low area just through a gate on the side of a house, or the low area between a flowerbed and the wall of a house, or standing water on or near a sidewalk or driveway.  These types of Drainage Problems are best served with Surface Drains.  A Surface Drain can move water away from a low area that is relatively small.  This can occur in yards, flowerbeds, sidewalks and driveways.  A Surface Drain is designed to move Surface Water away from a problem area to a predetermined exit point.  Surface Drains are available in many sizes.  How quickly they remove standing water is usually determined by the size of the Drain Pipe that is connected to the Drain.

Surface Drain Installation in Norman

Simply put, a Drainage System is one or a group of underground Drain Pipes that take water away from a place that has water standing on it or flowing across it.  The water that is in the problem area, can be causing damage or may be inconvenient or both.  (Usually Both)  A simple Drainage System is a Drain for the water to enter, a Drain Pipe to move the water away from the Drain, and an Exit Point for the water to be released out of the Drain Pipe.

Drainage Systems quickly can become more complicated.  Considerations must include:

How does the water get to the problem area?  There may be one or many sources.

Water Sources:

1.  It falls from the sky directly

2.  It flows down hill over the surface (surface water)

3.  It flows underground under the surface (sub-surface water)

4.  It flows from the edge of a roof ( There may be many roofs near the problem area, neighbors etc.)

5.  It flows from a gutter downspout

6.  It flows over the edge of a gutter because the gutter is too small is is clogged

7.  It flows up from the ground (seeps and springs are common in Oklahoma)

8.  It flows from a sprinkler system use ( yours or your neighbors)

9.  It flows from a leaking pipe ( water mains, water meters, water lines, sprinkler pipes, sprinkler valves)

There are other reasons for Drainage Problems, the above reasons are just the most common.

Once the number of water sources is determined, a rough estimate of the amount of water that needs to be drained away on average must be estimated.  This can be simplified down to “SMALL, MEDIUM, OR LARGE AMOUNTS OF WATER TO BE DRAINED AWAY.  You don’t have to be an engineer trying to calculate fluid dynamics.  Experience at diagnosing drainage problems helps however.  How much water needs to be moved will help determine the type and size of the Surface Drain or French Drain that needs to be installed.  It also helps to determine the size of Drain Pipe required for the Drainage System.  A good rule to follow is, “If in doubt, install a larger Drain and Drain Pipe.”  Unused Drainage Capacity is better than property damage caused by a Drain that is overwhelmed by too much water.

For home and small business use typical materials used are:

6 inch, 9 inch, and 12 inch Surface Drains –

3 inch, 4 inch, and 6 inch Drain Pipes —

3 inch, 4 inch, and 6 inch French Drains —

French Drains move more water than Surface Drains —

French Drains move Surface Water and Sub-Surface Water

Surface Drains move Surface Water only

Surface Drains look nicer than French Drains in most cases

Once the type and number of drains is determined and what size Drain Pipe will connect them, an exit point must be selected.  (Where is the Drainage System going to take the water to and release it?)

The Drainage Curb Fitting is installed when the desired exit point for the French Drain will release the Drainage Water into the Street.   The Drainage Curb Fitting is rectangular in shape and made to be installed through the curb.  A small section of Curb is cut out with a concrete saw.  The Section is a few inches wider than the Drainage Curb Fitting.  We then install new concrete around the curb fitting.  Once the concrete has dried, the Drain Pipe coming from a French Drain or Surface Drain is connected to the Drainage Curb fitting and then covered with dirt.

Cutting The Curb and Installing Curb Fitting for French Drain

The Drainage Pop-Up Emitter is connected to the end of a Drain Pipe.  It is downhill from a French Drain or a Surface Drain.  It is a small release basin with a green pop-up lid.  When releasing water, it pops up about an inch to release the water from the French Drain or Surface Drain.  When the Storm Water has moved through the Drainage System and out of the Pop-Up Emitter, the green lid closes back to its original closed position.  The emitter is designed to release water out into a yard or down a hill or other desirable Drainage Exit Point where there is no curb.

Popup Emitter to release water from a Drainage System in Yukon.