French Drain Oklahoma City, Norman, Edmond, Mustang, Moore

Oklahoma Drainage – x We install French Drains, Channel Drains, Surface Drains, Sump Pumps and Sod.

If You live in Oklahoma City and water damaging your foundation, We can install a French Drain for you.

If you live in Norman and have water standing on your driveway, We can install a Channel Drain for you.

If you live in Edmond and have water flooding your basement, We can install a Sump Pump for you.

If you live in Moore and have water washing out your flower bed mulch, We can install a Surface Drain for you.

If you live in Yukon and need grass to grow we can install Sod too!

Oklahoma Drainage – 405 203 9419

Storm water can cause all types of problems in and around your home.  We are dedicated to solving all types of Drainage and Standing Water Problems.

 

French Drain Connected to Channel Drain

 

Installing Curb Outlet for French Drain in Oklahoma City

  We service all of Central Oklahoma including Edmond, Oklahoma City, Moore, Norman, Midwest City, Del City, Purcell, Blanchard, Newcastle, Mustang, Yukon. Now servicing Lawton and Altus.

 

Drainage System Installation in Norman

French Drain installation is a big focus for Oklahoma Drainage and Sprinkler Repair. A French Drain is one part of a Drainage System. A French Drain can be connected to other types of Drains or Gutter Down-Spouts and then run through Drain Pipe to an Exit point where the water is released.

A Drainage Exit Point is the area where water goes to be released when it comes out of the Drainage System. The two most common exit points for a Drainage System are a Pop-Up Emitter or a Curb Fitting.
A Pop-Up Emitter is a Fitting on the end of a Drain Pipe that has a lid that pops up and releases water. When water drainage is complete, the lid shuts back.

Pop-Up Emitter for French Drain

Just what is a “French Drain?”  Many times people incorrectly use the phrase, “French Drain,”  to apply to many different types of Drains that could be used in a Drainage System.  The term is widely used and many times incorrectly connected to “Surface Drains,” or “Channel Drains.”

A Surface Drain has a grate that sits on top of a basin.  The basin is underground.  A Drain Pipe is connected underground to an outlet on the Drain Basin.  Storm-Water Drains through the grate into the Drain Basin.  Once in the Drain Basin, water travels out of the basin through a Drain Pipe.  The Storm-Water continues downhill in an underground Drain Pipe to an exit point.

Surface Drain in Edmond Oklahoma

THIS IS NOT A FRENCH DRAIN!

A Surface Drain may come in many different shapes or sizes.  The Drain Grate may be round or square.  Here is a picture of a common Surface Drain.

Channel Drain Installation

A Channel Drain is a type of Surface Drain and many times is installed in concrete across sidewalks or driveways

A French Drain is completely different from a Surface Drain.  A basic French Drain consists of a Perforated Drain Pipe in the bottom of a trench.  The Drain Pipe should have a neoprene sock around the Perforated Drain Pipe.   This is to ensure that the Drain Pipe does not become clogged.

The dirt that was taken out to make the trench is hauled away.  It is replaced by some type of small stone or gravel depending on what is desired or available.  I prefer crushed 1 inch lime stone.  It is the most economical option in my area.  Pea Gravel or some other type of small stone can work just as well.    The lime-stone or gravel is placed in the trench on top of the perforated Drain Pipe and filled all the way to the surface (ground level).   In some cases where the French Drain needs to be deep or is being placed in sandy soil, a special trench liner must be placed in the trench before the perforated Drain Pipe or the Gravel are installed.  This helps maintain the integrity of the trench over time.  It also increases the cost of the French Drain and the amount of time to install it.  I install a trench liner in a French Drain about 20% of the time.  Most of the time a liner in not needed.

French Drain March 2011

A French Drain is designed to handle a large volume of water and cover a large area. The Drain is anyplace the trench goes. It has many applications and can be used in many situations.  It can be installed by itself or incorporated into a Drainage System with Surface Drains or Gutter Down-Spouts connected to it.

The main downfall of a French Drain is, that they, for the most part aren’t very pretty.  They don’t look very nice in a yard once they are completed.

Depending on the area the French Drain is installed and the type of grass around the French Drain, will dictate whether grass grows over the lime stone.  Grass can grow up and through the gravel in the French Drain over time eventually covering the gravel.  This is Ok.  It won’t have a measurable effect on the performance of the drain.

DON’T COVER THE GRAVEL IN THE FRENCH DRAIN WITH DIRT.  THE FRENCH DRAIN WON’T WORK IF THE TRENCH IS CLOGGED WITH DIRT.  DON’T EVEN INSTALL IT IF YOU ARE GOING TO COVER IT UP WITH DIRT.  PUTTING DIRT OVER A FRENCH DRAIN IS LIKE PUTTING A CORK BACK IN A BOTTLE.

DECORATIVE STONE CAN BE USED TO COVER A FRENCH DRAIN AND THEY LOOK GREAT AND LAST A LIFETIME.